I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi,
I'm working with the nRF54LM20 DK (nRF54LM20A) and evaluating whether it can act as a USB host to read data from an external USB CDC ACM device.
The intended setup...
Hi
I remember the Devzonw could ask for hardware instructions. My matching circuir has used the nRF54L15 reference design and nRF21540 DK design, all the value is the same...
I used binwalk to analyze the zephyr.signed.encrypted.bin file generated by the routine mcuboot_with_encryption. I found that the firmware was not encrypted but merely compressed...
We have a peripheral device that maintains a PAwR sync (as a syncer/responder), connects to another peripheral in a central role, and also accepts connections from a central...
I tried writing read and write code for sEMMC based on information obtained from an AI assistant. The resulting code is shown below:
As you can see, the block address...
I used an oscilloscope to check the waveform and found that only the clock and IO0 had waveforms. I am using this interface to send data:
nrfx_err_t nrfx_qspi_write (...
This is just simple feedback on the nRF Connect Toolchain Manager v0.9.2.
The download speeds when installing an SDK are terribly slow. On a 1Gb /s connection my PC was...
Hi Nordic team,
We are currently migrating our project from nRF Connect SDK v3.1.1 to v3.2.4 on the nRF9160 .
Our application was working without issues on v3.1.1. After...
I am working with:
NCS Version: 2.6.1 (SoftDevice Controller)
Hardware: nRF52x Platform
on a custom board (nRF52 series) and I'm trying to achieve a "Headphones...
Good morning,
It has been implemented a sleep mode to save battery when the board is not used.
To do that we follow the documentation and implemented the SystemOn mode...
Dear:
I am using SDK12.3 with S132 write application using BLE+DFU+UART+I2C, The device connects and communicates with mobile devices through our own application(ONF Link...
I understand that in %XSYSTEMMODE the flags are not just for fun so practically what are points to do not enable the GNSS always even if I do not use it? I do not care on...
HI
I am currently doing secondary development based on the periodic_adv_conn sample project, using NCS 3.2.1 and the nRF54L15 chip,PHY CODE S8.
I want to add a function...
Hi， We use 52840 based on NCS3.2.4，add UART1 to blinky example because I need to use UART0 to log and UART1 to communicate with MCU for our application. The UART1 could send...
