I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello, I recently acquired the thingy53 device and I am trying to use the example of the weather station with matter:
Weather Station . I am following what the documentation...
I've built a simple Matter device for the nRF52840, using the chip-build-nrf-platform Docker image.
The host OS is Linux, and I mapped the physical device ( /dev/ttyACM0...
Dear nordic,
state of your MCUBoot + Immutable bootloader is just awful.
Please fix this hook, when enabled it disables updates of the mcuboot bootloader when used with...
Hi,
From nRF5340 audio example kconfig, there is a note that "now 48kHz is the only sample rate supported". Is this correct? My application would only work for lower bitrate...
Hi,
I have a RIGADO BMD-300 module that can only be accessed over the air. (no physical access)
The modul has the BMDWare ( https://file.elecfans.com/web1/M00/20/D2/oYYBAFmk2JOADMegAAu4fGDEUUo022...
Hello,
I am looking at using the nRF52832 for a safety-related purpose and therefore want to isolate the safety-related code away from the Bluetooth stack. The main concern...
Hi,
I have observed a strange behavior when manually selecting wrong PLMN. I get EMM reject cause 11/PLMN not allowed as expected, but then the modem is stuck in CEREG state...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v2.0.0 Hello. In my project, I want to make sure that my project always works during power on. How can I check if my project can...
I am using a nRF52832 with a LISD3H accelerometer. When I initialize the twi driver, I see a ~250 uA increase in current. I was hoping to initialize the twi driver, enable...
Hello,
I use nRF52832 and SDK 17.02.
I use app_button library to detect and handle button pressing.
Everything works fine except that I have a testcase that is to...
We have a very simple application with an out-of-tree driver that is working fine with NCS 2.0.2.
However, changing to NCS 2.1.0 or 2.1.1 results in a DTS error:
(the...
I am working on a project that uses image differentiaton,person/animal detection, etc. To accomplish this, I can either use OpenCV library or use TinyML lite. The problem...
Hi Nordic:
Maybe it isn't a really question. When I try to make an error check, I get two types of error checks, ERROR_CHECK() and APP_ERROR_CHECK(). It seems to be the...
