Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi there,
The mentioned known issue needs a workaround requiring a soft reset. This is quite a bruteforce method and I can't believe this hasn't been fixed already. Quite...
nRF Connect SDK v2.0.0
VS Code 1.70.2
nRF9160 development kit
To view all possible log messages the fololwing logging configuration is set up in prj.conf:
CONFIG_LOG...
I'm using nrf52832, and it is connected with external mcu (stm32) to uart.
I'd like to connect this ble module to PC with ble (wireless connection), it was paired.
After...
Hello,
We developed a zigbee coordinator with nRF52840.
We discovered that our coordinator is not receiving the the beacon request coming from some Ember based sleepy...
Hi,
Is it possible to connect the Thingy53 over Bluetooth with Raspberry and store the sensor data in a database (e.g. Firestore).
I only found one solution, but its for...
Hi,
Is it possible to get the device name - i.e the GAP_DEVICE_NAME - of an unprovisioned or provisioned device using a serial device and the interactive_pyaci? It would...
Hi everyone,
at the moment we are trying to upgrade our nRF9160 software form the SDK v1.8.0 to the newer version SDK2.0.0. The main issue of the migration is our UART implementation...
Hi,
I'm using NCS v2 and VSCode on a custom board, and the android nrf connect app.
The board which has an external crystal, which I am not trying to use, in favor of...
Hi,
I am migrating to use Advertising Sets, which require Extended Advertising, and I am seeing that the number of connections per-connectable-service is seemingly reduced...
Hi,
I have been successfully working with CoAP customized client/sever app for a custom dev board. This custom dev board was based on Minew MS88SF21 module. I have created...
Hi,
I create two extended adverts, one connectable and one none, (nRF Connect 2.0.0) using the following code:
This works great, but then i want to amend the data...
Hi, I have just started looking at integrating Matter in my devices and am looking to measure voltage. However, there is no cluster under the matter clusters that matches...
Hi,
There is a loose wire on our PDK, The right side is on the cap, but the left side is loose and not clear where it came from. Can you help?
Regards,
Peter
Hello everyone,
In my application, and in samples I have studied, the A-GPS data request starts with the NRF_MODEM_GNSS_EVT_AGPS_REQ event when the modem wakes up/is started...
I'm in the project in which we are trying to implement logging to file functionality to NRF5340 chip.
Following lines were added to config.proj file:
# experimental...
