Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi!
I'm developing an application that requires both keyboard and mouse control over BLE. I have gone through various guides to get this working, and the only method that...
Hello!
I'm developing firmware for a custom board based on nRF52811 CAAA. I am trying to create a new board under .\v1.9.1\zephyr\boards\arm\nrf52840dk_nrf52811_myboard...
BT central sample has the following code
bt_enable ( NULL );
bt_le_scan_start (SCAN_PASSIVE , device_found );
I ran the sample on my custom board based on nRF52840...
Hello,
I'm using the UART0 in nRF52840-DK for debugging purposes and using the ble_app_uart_c example as a basis.
Now, I need to activate and configure the second UART...
Hi guys
I'm just want to know, is this situation can occur if my application size will grow so high that it could be overwritten by the flash data storage module?
...
I am developing for a Thingy91 and NRF9160 DK
NCS v 1.9.1
I am using the LTE_BLE_Gateway sample using the NRF9160 as the Host and talking over HCI to the NRF52840 as a...
Hi
I'm working with ringbuffers ( docs.zephyrproject.org/.../ring_buffers.html ). I'm using the data item mode. Periodically I put data into the buffer (if I'm correct,...
Hi there,
We are trying to integrate an nRF21540EK shield onto our nRF5340DK. Following the instructions on the following link ( https://developer.nordicsemi.com/nRF_Connect_SDK...
Hello
My production ble performance is lower then nrf52DK.
How can I impove ble performance?
And I think there are two ways.
1. redesign PCB antenna (currently...
So, I'm trying to debug some code I've been working on, so set CONFIG_LOG=y in my prof.config file.
Now, when I try and builld, I get this error:
Error: Image size (0x36c54...
Hello everyone,
I am using the nrf52840 on the CDEBYTE E73-2G4M08S1C nRF52840 BLE 5.0 Wireless Transceiver. robiz.net/e73-2g4m08s1c
There are two device. One of them central...
nRF52840, SDK version 17.0.2_d674dde, SD140.
Our code uses the PPI extensively to manipulate some GPIOs and start SPIM transfers from peripherals using EasyDMA to store...
Hello all! I am trying to interface MPU6050 with nrf52832 dk using the following code. On the LOGGER, I see that the MPU isn't detected, despite I replaced the MPU. The if...
