Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi,
I use the a gpiote_in_event to trigger a number of PWM pulses which works fine so far. However, the exact behaviour of the generated signal is important so that the...
Hello, I am using nRF52-DK with Segger Embedded Studio and I'm running the following code that first blinks the LED1 on&off 5 times, and sets up BUTTON1 for wake up, and then...
Hi,
I would like to read the temperature of the nRF.
I tried to use the routine I found here in the forum
Sometimes works sometimes the system crash. I notice the...
Hi
I am using NRF5340 chip in my custom board to communicate serially with an external device whose data length is more than 128 bytes.
The chip can receive 243 bytes...
I am looking for the examples for the SDK. I installed SDK 1.9.1 through the Toolchain Manager and see the directory "users/my_user_name/ncs/v1.9.1" Supposedly this is where...
Hi,
In Openthread's Coap_client sample, Following 2 libraries are there:
and while compiling my code I get multiple warning regarding to above 2 libraries.
Following...
Hi,
I have problem to use bmi160 library with nrf5340 in spi connection.
I use the example application zephyr/samples/sensor/adxl372 and change the sensor to bmi160 (...
Hi DevZone ! Here is my issue: I use to work with VSCode and nRF Connect for desktop for a few months now. Early on Monday, I did uninstall all my dev environment (VSCode...
Hi,
is there any way to get a Pin to a defined "high" without vdd-gpio ref?
In our situation the NRF9160 Power is a Battery with 4,1V and the VDD-GPIO is 3,3V with a regulator...
I created two build configurations a Debug and a Release in SES IDE.
Build > Build Configurations...
I wanted to select the DEBUG_OPTIMIZATIONS level for the Debug build...
This is a continuation of the topic here that is now closed
https://devzone.nordicsemi.com/f/nordic-q-a/85590/nrf9160-azure_iot_hub-change-dps-username-during-run-time ...
Hi, I want to update the modem firmware devices(in the field).I am using nRfconnect sdk 1.5.0 and hardware is brf9160 SICA B1 . current modem firmware is 1.2.3 . I tried to...
I tried to define an event as in attached figure. During Build, the error in the as shown in the attached imageoccurs. Where to define Log Configurations ? I ading custom...
cpu info:nrf5340
software:nrf connect sdk 1.6.1
hi professor,
In the uart interrupt I call k_fifo_put to trigger rx process thread but it is not take effect.What person...
Hi,
we are developing a system based on device with nRF52840 S140 ( central and pheripheral).
We developed on both side a custom service.
System is working fine bonding...
