I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi
I am currently trying to get the antenna switching working on the nRF52833 DK
I have an SPDT RF swtich is this pe42423
1.I want to use for switching.But I don't...
Hi,
I have a central-peripheral FW over a nRF52840-DK running NUS service and I have to measure the throughput between the nRF52840-DK acting as a peripheral of a mobile...
Hi
How do pass bat_num into the declaration for the power config attribute list? Perhaps I overlooked it, but it wasn't evident to me when reviewing the Developing with...
Hello All,
First, thanks for this post: https://devzone.nordicsemi.com/f/nordic-q-a/40924/how-can-i-restore-the-original-bootloader-of-a-pca10059 ; I'm attaching the file...
Hi. In nrf52840 is it possible to use in NRF_LOG the second UART (DMA based) ?
I know i can define the TX pin in the SDK_CONFIG but can the NRF_LOG_BACKEND_UART work with...
Hello I am trying to get the usb cdc acm module to work for the nRF52840 dongle. However, the example is made for the dev kit. I flashed the dongle with the example anyways...
Hello,
We are looking at using an nRF52 Series microcontroller for a BLE device. We are trying to decide if we should use the nRF5 SDK (which we have used in the past) or...
Hi Nordic team
1. Define one vendor client model and one vendor server model at mesh nodes.
2. Provision all mesh nodes. Then, Create a mesh group 0xC000.
3. Configure...
Hi - Recently, the NRF Connect Toolchain manager stopped being able to open VS Code and hangs spinning - screenshot below. It used to work so I'm not sure what's changed....
We want to verify that the modem can find mobile networks without actually connecting. Actually connecting to the network has a price tag. The context here is a quality assurance...
Hello, Support
I am new to Nordic and try to follow the tutorial video here https://www.nordicsemi.com/Products/Development-tools/nRF-Connect-for-VS-Code/Tutorials
Just...
Hello all,
The sensor (VCNL4035) is connected and found by the nrf52dk. Indeed, the twi_sensor/scanner have been quickly recoded and it shows some progress...
The manufacturer...
Hello,
I am using ble_app_uart example in sdk 15.2 and nrf52832.
I am using this example to communicate with other MCU. It is continuous Rx Tx between nrf52832 and other...
Hello,
I am currently implementing a security protocol from the IETF LAKE working group called EDHOC in Rust. I am using nRF5340dk and the bare-metal Rust examples from...
Hi there,
I am currently following this following tutorial on building a Matter setup.
When trying to build the openthread coprocessor I am hit with the following error...
