The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi everyone,
After the latest update of the nRF Connect SDK plugin for VS Code (2025.4.106), we've seen this pop-up appear. We are using v1.8.0 and now we are not able to...
Assume the nRF21540 used as a front end for nRF52840. When the nRF21540 module is in power down mode can it pass the signal without significant loss? If yes what is insertion...
Hello,
I've searched a good amount of online content, but I cannot publicly find a good enough reference design for the nrf52840-DK, natively compatible with Kicad.
...
Now I can use LIBUARTE to receive data from MCU, but have a trouble: it can't receive a whole packet sometime,and return it with 2 parts.
UARTE : 115200/8/1
receive buffer...
Hi Support Team
I installed the NCS V3.1.0 just now. But there was an issue of west: unknown command "build" for the NCS V3.1.0 when I built a sample. Many thanks.
Hi,
I'd like to raise this issue I am having with the v3.0.1 sdk wherein the final build stages I get the message attached
I am using the Lesson 9 exercise 5 sample...
I am trying both v3.0.0 and v3.0.2 SDK; the board I am using is the nRF9160DK, version 1.1.0. There are 4 scenarios:
1) Run on Linux (minicom or Serial Terminal) following...
Hi Support Team
Our product have a CD 4kv and AD 8kv ESD test, but the samples reset on AD 8kv close to the USB, the reset register show it is nRESET PIN reset.
add an...
I'm having several problems with the Intermediate course, L2_e2. In Step 3 it says that there is 'a bug in coredump_gdbserver.py that causes a crash if building with optimized...
I need to use a nrfx timer in order for some GPIO timing, but can't get past the simple examples declaring an instance. For testing I'm just using the 54L15DK.
I was using...
Hi,
I would like to create a UART on the nRF54L15 DK, but currently it seems that only the pins bound to CONFIG_UART_CONSOLE (P1.04 / P1.05) are working as below Output...
HI there,
I like to configure and use the COEX Interface with the COEX Pins for DECT-NR+
on a nrf9151DK Board: https://docs.nordicsemi.com/bundle/ncs-latest/page/zephyr...
I am trying to compile my custom BLE application into Babblesim using the nrf5340bsim/nrf5340/cpuapp board in nRF Connect SDK v3.1.0. The application uses PSA Cryptography...
I wrote some firmware that I got working with the Nordic nRF52840 Dongle. It acts as a USB device, you can see under the device manager on a computer when you plug it in....
