Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Hi !
This is more of a question than an issue. I am curious about the future of TF-M and its implementation on Zephyr. Does anyone know what are the plans on Zephy's or...
I'm trying to set tx power to +3db in the peripheral_uart sample.
I don't need dynamic control, just setting to always use +3db.
Adding the following line to prj.conf...
Hi,
I am using coded BLE to connect two board using nrf52840. I just let bluetooth to run, then measure power consumption of the peripheral board by measuring the current...
Hi,
I am trying to send messages from my gateway, which has UART and __LOG enabled, to a specific LPN address (0003).
So I want to send messages from my FN Light1 (0002...
We have developed an application in ncs-1.3.0 where we created a west.yml file for the application that lists nrf, zephyr and other dependent repositories. We have downstream...
Hello. everybody.
I'm new to be here.
Now, I'm struggling to succeed in building 'ble_app_beacon_pca10040_s132.uvprojx'.
(This file located in C:\(private dir)\nRF5_SDK_12...
We encounter 52810 freezing problem. It occurses in low probability less than 1 out of 1000.
Power-on reset is no use for this problem. The freezed 52810 chip restored when...
Hello,
I am developing a product that acts as a peripheral and sends a notification of more than 20 bytes (which is by default the BLE MTU). How can I config the MTU so...
Hallo I'm writing Data to the I2C port.
I'm using the nrf_drv_twi_tx function. It works well.
But I want to write bytes to the I2C without Adress. - i want to write just...
Hi,
I have the nrf5340 development kit. This is my first time working on Nordic devices. I've followed the Getting Started Guides. I am trying to run the first test. My...
Hi,
I'm trying to m ake sure that the nRF Sniffer files can be run correctly, following the instructions: "On Windows, type nrf_sniffer_ble.bat --extcap-interfaces".
The...
Hi,
Can you please explain what is the usage of unconnectable advertising? And what is the difference between beacons and unconnectable advertising?
Thanks!
What does (15U) mean ? Is that a specific useage declaring a number?
What does " =='\n' " means ?
After a long period of learning , I'm now trying to read and understand...
Hi everyone,
I am making a zigbee mesh with just coordinator and routers only. I intended to have the mesh to cover a very large areas with nodes that can be moved (not...
Hi,
I have got some problem of understanding the IQ sampling data.
As below is the official data format
0: I_Q (default)
Q
31:16
12 bits signed, sign extended...
