hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
I am trying to define a simple output pin.
in the DTS file I have:
aliases {
ledred = &hwledred;
ledgreen = &hwledgreen;
memwp = &hwmemwp;
};
soc {
gpio0...
I'm implementing an OAUTH procedure on my device. I'm able to access login.microsoftonline.com and get user and device codes, then after authorizing, I can access the token...
LE audio demo,i enable CONFIG_STREAM_BIDIRECTIONAL ,when i connected Galaxy Buds3 by cis.
my uart_tx will stop.cpu looks busy.when disconnect with headset.data will...
Hello, I have a problem trying to connect Direct Test Mode desktop app to my custom board running Zephyr on nRF52833. My firmware sample is based on hci_uart https://github...
Hi folks,
I've been trying to use the sw_pwm to generate two PWM outputs. I'm using sw_pwm because I want to achieve lower frequencies (1-100Hz) and the hardware PWM API...
Hello,
I need to connect the Thingy:91 to an MCU via UART and/or SPI bus. I need help to identify the pins for communications for:
SPI: CSK, CS, MISO, and MOSI
UART...
Hi, I am new to working on the display . I am trying to integrate nrf5340dk board with waveshare lcd module which is of 1.14 inch and has st7789v controller by using SPI communication...
Hi,
Legacy SDK bootloader and dfu preparation workflow had the following option:
hw_option allowed for checks, whether supplied firmware matches given hardware. So firmware...
Using nrf5340 audio DK & ncs v2.60
I modify this function to print this information when the number of packages reaches 100.
\
Part of the result:
120*100*8/(...
Hi, I'm trying to implement timer synchronization on one central and multiple peripherals, I'm using nRF52840 and NCS v2.8.0. I've seen the example conn_time_sync which uses...
Hi,
I am using download client for downloading a file.
I am using download_client_get and get fragments in callback.
When the file requested is short in the callback...
Hello Nordic Team,
I'm developing a project with two nRF52/nRF54 microcontrollers where I need: - 1st microcontroller as BLE peripheral receiving mobile app data (nRF connect...
I'm migrating code from ncs 2.7 to 2.9.
I am using CONFIG_BT_EXT_ADV and scan timeout callback - such timeout requires CONFIG_BT_EXT_ADV:
It was working fine. Now it's...
Hi,
I follow the custom board exercise steps with mynRF52840 DK and when I reach step 8.1 , in the deviceTree visual editor, I notice that the GPIO0/1/TE options under ...
