Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hello,
I have a problem with the GPS and more precisely the AGPS. I would like to retrieve my position with the thingy91, I created a project by taking the AGPS sample and...
So, for a while I have tried to follow these instructions: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.meshsdk.v5.0.0%2Fmd_doc_user_guide_modules_dfu_configuring_performing...
Hello,
Developing on Zephyr 1.2 and modem fw 1.2.
Developing a client LTE application. If I run the below sequence of commands periodically every 2 min:
eventually...
Hello everyone,
I am working on an nRF52-DK and getting familiar with Zephyr.
In this process, I am trying to connect with the sensor API with a "fake" sensor whose...
I'm not certain where to send suggestions, so hopefully this will do...
A very useful addition to the nRF Connect SDK would be support package documentation for Zephyr...
Hi,
I am trying to run the NCS Zephyr ADXL372 sensor sample application (using nRF5340 DK) but get the following error:
This corresponds to the following NACK error: ...
I would like to do mutal TLS on a NRF9160. I found the https sample where the firmware does server authentication. How do I add client side authentication to this example...
I have a project from 3 years ago (2018) that I'm trying to make a simple update to the application code. The code downloads via the Segger Embedded Studio and runs correctly...
A vulnerabilitiy in BLE secure connections is reported as CVE-2020-26558 : Impersonation in the Passkey entry protocol
"The Bluetooth SIG is recommending that potentially...
My application uses a NRF52840 (SD140, SDK 15.2.), very simple circuit and needs to be extremely low current consumption. I measured the current in conditions of BLE on and...
I'm trying to get a BLE example for NordicSemi nRF52833_xxAA using SoftDevice S113.
I found out only two examples but they don't compile.
Error[Go029]: Variable "sec_mode...
Hello,
Is it possible to disable the antenna pin of the NRF52 in software? I cannot see anything in the data sheet which suggests this.
We are using a third party module...
While following the steps required to provision the nRF9160 Connect for Cloud certificate, I entered the 'AT+CFUN=4' in the AT command text field and I clicked 'Send' but...
I have a working code using SoftDevice 140 7.2.0 and Segger ES on the nRF52840 DK. I made the single adjustment of the preprocessor variable BOARD_PCA10056 to BOARD_PCA10059...
Hi,
I use example projects from Nordic Thread: CoAP Client and Thread: CoAP Server with Segger Studio Nordic Edition (projects use Zephry which is generated by NRFConnect...
