Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
I am trying to port my build from Eclipse (based on the GCC tool chain) to a KEIL uVision build system.
I am using KEIL ARM Compiler version 6.15. Most of the files compile...
I see many similar questions to this, but I want to double check my understanding.
We have the nRF52840 connected to D-/D+ on a USB Type-C connector. We have a standalone...
Hi all!
I'm using an nRF52833, SDK 17.0.2, s140 softdevice 7.2.0. My design uses a Skyworks SKY66112 amplifier.
I have the pa_lna_assist function that I found here on...
I am running the example:
C:\Nordic\nRF5_SDK_17.0.2_d674dde\examples\dfu\secure_bootloader\pca10040_uart_debug\arm5_no_packs
Everything seems to be working well except...
Can you please provide security manager keypress notification sample program for bot peripheral and central program. I want to know why it is used and what is the main purpose...
Hello Nordic team
I am developing a BT mesh network project, which be implemented by nrf52840. Right now I am designing the node PCB. I want use the No.4 reference circuit...
Hi,
I tried to implement my custom service.
I followed the tutorial from this site: https://github.com/bjornspockeli/custom_ble_service_example
For SDK 15.0 it works...
I'm attempting to connect an SDcard (micro SD) to an nRF52840-DK via a breadboard setup. I'm running Zephyr and it appears that configuration is to be performed via device...
I'm trying to investigate whether I should ditch BLE in favour of Gazell and ShockBurst (to avoid the $8000 Bluetooth.com fee)
I've noticed that Gazell has no entry in the...
Hello,
I've got this Thiny:91 demo working nicely, but what I'd like to do now is only measure RSSI.
Is there firmware to only do this?
Like send AT commands only to...
Hello,
I've been trying to perform a dfu to a target Nordic device over Bluetooth using an nrf52840 dongle distributed by Laird, however whenever I attempt to run the command...
Hi guys,
I am trying to create a zigbee mesh with 10 devices with 1 coordinator and 9 routers (all are nrf52833 based custom board). I can create a mesh network easily with...
Hi,
I understand that white list can be enabled at the peripheral side. I also know that if white listing is enable on the peripheral side then it wont respond to centrals...
Hi All !
Hope you are doing well !
I have tested some examples using SDK 17.2.0 and it worked fine ! .IDE i used is SEGGER IDE . Now i have a question that my next HW...
Hi,
I'm testing the USBD BLE UART Example with nRF52833 DK, after programming the app, the LED3 keep it off all the time as followed.
In the device manager, I can see...
