Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
I’m facing a UICC failure issue on multiple nRF9151 DKs.
Symptoms:
AT+CPIN? returns ERROR
%XSIM: 0,9
SIM VCC is not present (no 1.8 V observed)
Nordic stock examples...
While developing my project, I need to receive UDP packets with the NRF9151. My configuration is as follows: - 1nce SIM - VPN between my UDP service and the 1nce network ...
We are using a custom board based on nRF54L15 with MCUboot and compressed image DFU over OTA. DFU was working correctly when updating between NCS v3.2.0 and v3.2.4, but after...
Hi everyone,
I need to implement a coded Phy ble communication in a project and for that I wanted to use an nrf52840 dk. However, for it to be able to compete with the Aircable...
Hello Nordic Team,
I am currently working with the nPM1300 EK together with the nRF54L15 platform and a custom 40 mAh Li-Po battery.
I am facing an issue while configuring...
I'm developing software for the nRF5340 based on the NCS 3.2.4 "hello world" example. Adding bt_enable() returns error code -11. Please tell me how to implement bt_enable...
Hello, I am developing a low-power nRF52840 product using the ncs Zephyr environment. Currently, I have suspended peripherals such as UART and I2C, allowing the system to...
Hello Nordic support team,
Forgive me if I am asking a stupid question.
In the source file ble_conn_params.c, there is a function called ble_conn_params_init() and I...
I've built the softsim external profile from Onomondo and it works. But when I try to incorporate it into the app I'm currently developing, it renders the code unable to boot...
I am trying to enter MCUboot serial recovery mode on an nRF5340 through a UART command.
I mainly followed the Nordic tutorial below:
https://academy.nordicsemi.com/courses...
I'm curious about the approach taken in the nRF Connect SDK's location library for cell neighbor scans ( https://github.com/nrfconnect/sdk-nrf/blob/main/lib/location/scan_cellular...
Hello, I am trying to use the latest nrfutil version 8.x.x in my custom project. Previously I had nrfutil version 6.1.7 with `nordicsemi` package included as a dependency...
I am trying to use the nRF54L15 DK board to flash a Fanstel BM15M module.
Fanstel BM15M module link: Fanstel BM15M Module
I am using the nRF54L15 DK board with the external...
