Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
We have the following setup:
- nRF52832 XXAA
- SDK 6.0
- S132
I have attempted to add a memory guard into the location preceding the application RAM data block start...
Despite following the procedure listed below, no text appears on the OLED display, despite the driver being able to communicate with the device.
I am using nRF Connect SDK...
I am looking to get some clarification on the QFN94 footprint of the nRF5340. There are four corner pads and they do not appear in the mechanical specifiications section 9...
Hi,
When looking at the reference schematics and reference layout of nRF5340 I notice that pins A25, B12, B26, G1, H2 and J31 are grounded:
Figure 1. Circuit configuration...
Hi, with my nrf9160 I need to send a gps location every 3 sec to azure, so I combined the agps and the azure iot hub sample. It's working pretty good but 10 sec as a periodic...
Hi, I doing PCBA prototype. And I found part number nRF5340-QKAA-R and NRF5340-QKAA-AB0-R7 in the website. In my understanding. The NRF5340-QKAA-AB is a sample engineering...
Hi,
I want to used NRF5340-DK for my BLE receiver evaluation I find LNA (NRF21540-DB) which is suitable to use with NRF5340-DK.
But I could not find this available in...
I am just beginning with the dev kit I bought in December. The box has a URL: nordicsemi.com/start52840dk
This is not helpful. The only thing I find there is a PDF - apparently...
hello,
i am using sdk 17 with ses v5.20 i have customised board consists of Decawave 1000 , Nrf52832 and accelarometer i want to compile and run both initiator and responder...
Please tell me about RBP CONF of UICR. Q1. What is the purpose of UICR's RBPCONF (read-back protection)? What kind of protection is it? Q2. What changes when RBPCONF (read...
I'm having problem connecting my thing:91 to the nrfcloud. When im trying to connect im getting "Troubleshoot nRF Code 40412". One of the reasons could be "before attempting...
Is there any way to run the TIMER peripherals off of the 32khz clock? We need to generate a 1khz PWM while the micro is asleep, and we really need to be able to shut down...
My device has BLE and I can successfully use any example (for example ble_peripheral/ble_app_bps ) to advertise different services.
It also has a serial port from where...
