Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Hello, i'm currently working on my Bachelor Thesis using Makerdiary Board. I recompiled the OpenThread Libraries to get the CLI working on my Board. I need to read out sensors...
Hello,
I'm trying to use UART0 for communications between the nrf52840 and another microcontroller, while also using UARTE1 for debug communications between the nrf52840...
Hi.
I'm trying to combine TWI sensor and BLE app UART examples.
I already tried putting parts of TWI sensor example in the BLE example, but it gave errors on missing...
HI everyone,
I have issue relate to ble_lbs_init(ble_lbs_t * p_lbs, const ble_lbs_init_t * p_lbs_init) function.
issue happened when i call: err_code = sd_ble_uuid_vs_add...
I am new with nRF9160, just bought a nRF9160 DK from overseas, but I use it in China, two questions come up.
1. Is it working with China celluar network?
I tried the Basis...
Hi,
I'm trying to make the softdevice controller work on NuttX RTOS. I followed the SDK example code to reproduce initialization. All calls are returning 0 (no error). However...
Dear Sir,
we're developing a Ble keyboard with 52810. the product needs to detect what kind of operating system and have different behavior therefore. but i don't know how...
As below, BLE Data RX works fine, but TX doesn't. When does this happen?
Currently BLE connect/disconnect and RX is working fine. The power does not turn off due to this...
Hello: I am trying to design a project about a type of sensor powered by high accuracy battery which is using the nRF52832 chip in a custom board. To use the battery energy...
Hi
My requirement is to upgrade the application firmware on the nRF52840-DK from another processor using SPI interface, and I am trying to understand the code to plug-in...
I'm developing a beacon application using the Fanstel BT832AF, which uses the nRF52810 internally. This unit is mounted to a custom board, but before raising a private ticket...
As instructed to post here by We're using Zephyr on at least 4 of our products and have thousands of boards with NRF chips in the pipeline; we're trying to get the consumption...
I'm trying to install nrfutil, but for some reason the installation is unsuccessful.
After installing python and the executing pip install nrfutil, restarting both the shell...
Hello,
when my application runs, from time to time I see the following:
[00:00:29.000,000] <debug> nrf_sdh_ble: BLE event: 0x26. [00:00:29.000,000] <error> app: ERROR...
