Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
In Mesh DFU, is there a way to change the public key on a set of deployed devices? I'm wondering if it's possible to rotate signing keys for our deployed devices that use...
Hello,
I'm trying to migrate my deployed devices to the nRF5 SDK for Mesh 4.2.0 (with connected nRF5 SDK 17.0.2). On the field I have several devices with nRF5 SDK for Mesh...
SDK is nRF5_SDK_17.0.2_d674dde, running on nrf52832, I migrate twi_scanner example to \examples\ble_peripheral\ble_app_gatts_c, if I set handler NULL in nrf_drv_twi_init(...
I used the "Toolchain manager" in nRF Connect for Desktop v3.5.0 to install nRF Connect SDK v1.3.1 on a macOS Catalina 10.15.7 system. This installed SEGGER Embedded Studio...
hi,
I am using nrf52840 (in a Laird module) and trying to advertise such that legacy BLE 4 mobile devices can connect. Only BLE 5 mobile can see the device (running nRFConnect...
Hi, I have a problem with the reset pin not working on the nrf52811. The firmware was developed on the nrf52840dk board and now that we are migrating to the real nrf52811...
Hello,
I have one SPI instance (instance 3, but have tried others) reading data from an ADC. It's reading data from an ADC triggered by a DRDY signal at 25khz. I setup a...
Hi,
I just enabled the CONFIG_BOOTLOADER_MCUBOOT=y for serial LTE modem application to understand the flash partitions and to perform the serial DFU(not sure if its really...
Hallo, using nRF52840 DK with Keil uVision 5.30, I try to debug the example ble_app_uart in the folder ble_peripheral, pca10056, s140. Compilation is OK, erase/programming...
please help me
I was working with LPCOMP when I set up lpcomp like above, even though I have set my comparator but just impacting anything on the AIN2 pin...
Hi,
I am using nrf52832 mesh board.I want to unprovision the device by pressing the button on the board.In the lc server example they handled it in rtt as it dont have hal...
Hello everyone, I am Smit and I am an IOS developer.
I am stuck to write data into the BLE device. Can anyone please help me out with this? Can anyone tell me how to do...
Hi,
I used the command line to install the toolchains as follows:
sudo apt install gcc-arm-none-eabi
It then installed version 9.3.1 of the tools on my Linux ubuntu...
Hi,
We have implemented a custom Watchdog Timeout handler, where we do the stack-dump. It has worked fine and we were able to analyze and fix the Watchdog resets. But...
