Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hello，
We are developing wearable devices. 17 sensor terminals send data to the receiver at a frequency of 60hz per second. The data sent by 17 sensors at the same time...
Hello,
I'm interested to know whether the continuous integration and continuous deployment (CICD) is possible on nrf52840 board using Segger Embedded Studio ?
if yes,...
Hi
I currently have a nRF52833 DK which I am using as a transmitter. I also have a custom board with a nRF52811 SoC with an antenna array to act as the receiver for AoA...
Hi,
I am trying to add PWM in my application. My application uses application timer, SPI (my own written code just like CMSIS) and BLE for smartphone communication.
Everything...
I am trying to integrate buttonless DFU with FDS in ble_app_uart example from sdk 15.3.0. Merge hex was done properly which includes bootloader_settings.hex+bootloader.hex...
Hi developers and researchers,
I am working on a project in which multiple nodes are communicating with each other in p2p manner.
My goal is to implement a multiple access...
In the AWS IoT example I have been trying to add RSRP support (i.e. getting RSRP when sending my data packet).
I registered the handler/callback function in main after modem_info_init...
Is the mcuboot module compatible with RTT logging? I've setup mcuboot and my main application but cannot see any logging.
I have the following in both prj.conf & mcuboot...
Dear all,
I just writing a little piece of code (no softdevice, using sdk 17.00), that in theory toggle a led based on 2 compare (CC[0] and CC[1]).
The strange thing...
I am using SD 132 6.1.1 with a GATT server and when the client sends a Read Multiple Characteristic Values command, the nRF responds with Request Not Supported. I need to...
Hello,
I bought the Thingy 91 and tried to follow the instructions on the getting started page.
I started by downloading nRF connect - Programmer v 3.5.0. Then downloaded...
Hi,
I have noticed ever since I updated my nRF9160 DK modem firmware to the latest version v1.2.0 frequent registration dropouts and very sluggish MQTT performance.
My...
Hi, I recently bought a Nordic Thingy 52 and it looks great ! It looks like there is a decent mic and speaker on the device and I was intrigued if the device could act as...
Hello,
I am trying to do communication with external module using UART0. But when I connect pin P0.28 (RX of UART0) to external module to receive the data, there is no data...
