Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
I have trouble when discover the BLE Peripheral that have the base UUID of characteristics and service are different. Then I followed several instructions in some cases, but...
I am trying to run the SDK15.3.0 gfx example code - only changing line 82 to:
And also I have changed the sdk_config to the display's width and height. I have wired it...
hi
I want to update RTC time in my device nrf52840 through nrf connect app. How can i do this? Is there any related example which may help me in doing this?
Hi,
I'm attempting to use OpenOCD to perform the equivalent to "nrfjprog --recover", since we've recently started using that feature.
I read through this case, but it...
Version 4.20a (Win x64) of Segger's Embedded Studio has problems with it's C syntax highlighting -- specifically conditional compiled sections of code. Code that is not being...
Hi,
We are using nrf52840 to develop a cryptocurrency hardware wallet. We want that user can verify that the device is authenticate. In order to authenticate, the desktop...
Hi,
I'm using Kail and I have a project with original target device nrf52832xxAA, I need to change it to nrf52832xxAB (the device onboard is nRf52832QFAB).
When I...
Hello,
I have to send SMS from NORDIC nrf9160dk which is using iBASIS sim card to my mobile phone. For this I tried two programs (at_client and simple_at). But nothing works...
Hello,
I am trying to run https://github.com/sigurdnev/fw-nrfconnect-nrf/tree/master/samples/nrf9160/i2c_scanner exampl. It is not compiling with the zephyr right now...
Hi,
for a new project we use the NRF52480, I can get it into low power mode with a total use of 20µA ( with all the other hardware on the board ). But when I initialize...
As far as I can tell, the packet sent by nRF24L01+ PTX only contains a destination address. There if no information that identifies the transmitter (i.e. PTX).
So, when...
Hi,
Just a small question, as the subject indicates: Is the power consumption for the Radio RX component (per µs) indicated in the Online Power Profiler for connectable...
Every time I try to connect to Android phone (running Android 7) or nrfConnect, it connects the first time. After I restart the nrf52 DK, the host takes a while to reconnect...
Dear Nordic support,
Now, I am using Nrf51822 to build up BLE Mesh network in my project on Keil C. As I found in here, Nordic doesnt support this chip anymore but is there...
