The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi,
I am using customized nrf52 board with softdevice s132
I am trying to interface External Flash (MX25L64) using spi.so when ever i am trying to send any command /data...
Hi
I figured out, that the macros in nrf_esb_resources.h are wrong.
You can find the used resources (PPI, TIMER and SWI) of the ESB library in Enhanced ShockBurst...
What is the operating and storage temperature range of nRF52840-DK development kit and USB dongle? We need to use these evaluation boards at a temperature range of -20 to...
Experts,
I'm trying to use NRF52480 Dongle to communicate over UART serial port. On the forum I found that pins 1.10 & 1.13 are used for TX/RX. I learned that flow control...
If i buy a raw nRF52832 chip and design the circuit by myself, how can i pre-programm the serial bootloader in it? So i could use the FTDI Basic (or an FTDI Basic -like device...
Hi,
Is there any way to change the advertisement name before switching to DFU mode?
I have a custom app that reboots into DFU mode (via NRF_POWER -> GPREGRET ). I want...
Hi,
I've to design an alimentation with capacitors to keep energy and filter current peak. To do that I need to know timing for NFC peak current. Do someone have information...
Hello,
I have a running system constituted of a central and 15 peripherals using nRF52840 devices. The central is set to scan the peripherals for 5 seconds then stop and...
Hello,
I'm implementing a beacon scanner with nRF52 using nrf_ble_scan.c. After the scan has been configured with no filters, no advertisement reports are returned to the...
Hi,
The definition of the COEX1 pin looks to be really interesting for applications that need a reliable time reference. A 1PPS GPS output is very useful; absolute accuracy...
Hi
Our nRF9160DK card seems to have stopped working. We attached a sensor to the card (We might have connected the reset pin on the P7 strip) and now I can't start any program...
I was trying to make sense of the serial support in mcuboot, but it uses a protocol and format I don't recognize. I expect they're generated by the Apache Newt tools, since...
I am designing a board based on the nRF52832 and wanted to examine the reference design files 'nRF52832-QFAx Reference Layout_v11.'.
However, The the downloadable files...
Hello!
I am using a nRF52832 with the S132 v4.0.3 softdevice. But I get an error from the softdevice via softdevice_fault_handler.
It gives me id 1(which suggest a NRF_FAULT_ID_SD_ASSERT...
Hi,
I'm using SDK 15.2. The bluetooth disconnects when I enable notifications on nrfConnect. This happens only if I increase the number of bytes to be sent. I'm writing...
