Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying add UART functionality in nRF5_SDK_11.0.0_89a8197\examples\dfu\bootloader.
After adding all required files and compiling program I am getting following error...
Hello I am using nrf52832 and I want to Calculate date and time at specific event periodically and save it to flash,so is it possible by using ble_app_cts_c example or any...
as title,
I can't load the project to SEGGER Embedded Studio.
I can't install CMake by entering the those command ( choco install -y cmake --installargs 'ADD_CMAKE_TO_PATH...
Hi
I was trying to do the page up and down key, I just built it successfully but it is no response.
Could anyone find out the reason for me.
I appreciate for your assistance...
Hello,
I tried to follow the "nRF_Sniffer_UG_v2.2" and i didn't understand the section 1.2 which described how to set the Python and Pyserial,can some one explain what to...
Hi,
1. Can one run the coexist sample with softdevice S132 on a mesh where all the other nodes run S140?
2. does the coexist (UART) example need to be provisioned. ...
Hello to everyone.
I'm working with the Light_Switch example with four nRF52832 SDK (two clients, two servers) and my cellphone as provisioner, in Mesh 3.10, with "nRF Mesh...
Hi again, Figure 106 in the OPS indicates that the application core and the modem core in the nRF9160 have separate Flash and RAM partitions.
Is this a "real" partition...
Hello,
I ordered my nRF52 DK from Rigado for their BMD-350 module using the nRF52832 chip, but their DK comes with an additional Atmel chip. Now I saw the regular nRF 52...
Hello!
In SDK15.3 project "secure_bootloader_ble_s112_pca10040e" for Keil , write flash incorrect and not work.
In SDK15.2 this prodject work fine.
Please correct...
My application will update over USB from a connected host.
For testing, I used two projects:
Bootloader: secure_bootloader_usb_mbr_pca10056
Application: led_softblink_pca10056...
So im trying to interact with a nrf52 chip. I am using iOS corebluetooth to communicate with the device and when the device sends a long data packet (~400 bytes) iOS drops...
Hi,
I have my SAADC configured with two channels. One for my sensor and one for the battery level measurement.
I only need to measure my battery level every minute for...
hi,i have a question.
nRF52832,can not Pairing and binding.SDK13.0.0,base onble_app_hids_keyboard example.
It can be paired and bounded before. but now can't pair and...
Hello,
SDK 15.2.0
SoftDevice 6.1.0
DFU with Uart (based on {SDK}\examples\dfu\secure_bootloader\pca10040_uart. Single bank mode as my app is quite big (probably not...
