The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi Nordic Team,
Meanwhile we are working with Laird BL654 which uses the nRf52840.
My questions:
1. Can we flash gazell examples on Laird BL654 with Segger?
2. If...
i'm trying to get distances between nrf52840 ble transmitter and receiver, using measured rssi upon receiving ble_gap_evt_adv_report_t from ble stack. in order to calculate...
In file sdk_config.h, in order to configure a calibration interval of 8 seconds, what number should be used in the define NRF_SDH_CLOCK_LF_RC_CTIV?
The time units are not...
Good day,
I again have an interesting question). There is a useful descriptor to better understand the purpose of the characteristic. This is a 0x2904 handle (GATT Characteristic...
Hi,
I want to know what event DEV KIT jump into when mobile provision complete for DEV KIT (100% , not bind app key and pub sub address). My idea is in provision process...
Hi!
I am currently evaluating the nRF91. For testing reasons I want to enable the debug logging for the lte link control. I checked the Zephyr documentation etc. but I was...
Hi everyone,
I am implementing a custom protocol using the NRF52 radio, and so far I was able to make the transmitter working as expected.
In a nutshell, the protocol...
I have a project about Bluetooth enable lock. I am going to use to BT832 module. Do i need recertifation for Bluetooth brand?. I dont know what to do. Do i need being member...
Hi!
We are developing an IoT device using the nRF52832. 2 years ago in this thread, https://devzone.nordicsemi.com/f/nordic-q-a/27099/nrf52832-ble-certification-under...
I'm combing over the CLI peripheral example, but having a few problems when running the example:
The Debug Terminal in SES blacks out the test so its difficult to see...
Hi I have developed and Android application to connect for 2 BLE Devices one after other.
These 2 BLE devices connection and service discovery will happen one after the...
Hi Nordic,
I am using SDK 12.3.0, S130 2.0.1 and PCA10028 nrf51 DK.
I would like to ask if central can make connection request without scanning (central know the mac address...
Hi everyone,
I have migrated my project from SDK for Mesh v2.1.1 to v3.0.0.
I am getting a Mesh Assert when the Mesh is trying to request a radio timeslot after the "NRF_EVT_RADIO_BLOCKED...
