Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Hello community,
I'm facing a problem with nRF51 DK PCA10028 and a function call on connected or disconnected state including NRF_LOG commands. Using SDK 12.3.0
On connected...
Hi, i have an existing product but the firmware has been removed from it. i have tried to use the dfu to replace the firmware but i dont know how to get the chip to the point...
The board has been working well.
Since one day, when I try to connect the board with my laptop using micro usb cable, the led5 starts blinking rapidly and I'm unable to...
Hi,
I'm trying to send and receive data to DATA interface that contains IN and OUT bulk endpoint (usbd_cdc_acm example). I'm using libusb on the PC side. It seems like I...
Hello,
I use PPK to measure the power consumption.
but I always get : Failed to start the PPK.
I have measured it last week and it is work.
and this is nrf connect...
Hi Team,
i am working on nrf51822 customized board, the SDK version is 12.3.0 (soft-device is s130 ) and Developing environment in keil 5.26 (on windows).
i am trying...
github.com/.../nrf52-ble-multi-link-multi-role I modified the code to access the environmental values and motion value
but if one thingy access one value such as temperature...
I develop an Android app which connects to a Nordic chip, and I cannot get the Android app to stop advertising once it connects to the central from the SDK multi link project...
Hi,
On the custom board I'm working on an nRF52832 uses the SPIS port with no CS signal (because of the HW connection with the master side of the bus). Since the internal...
Hi, i am trying to disable a signle GPIOTE channel via the INTENCLR. Here is a simple test case:
void gpiote_set_clr_test(void) { NRF_GPIOTE->INTENSET |= ((1<<3) | (1<<1...
Hello ,
I am working on a project in which two devices(one is central and other is peripheral ) uses Nordic bluetooth controller for connection and data exchange. nrf51822...
Hello!
I have been developing a BLE application on nRF52DK and used the ACN52832 as a module for a custom board for experimenting with BLE. I ordered a custom PCB from...
I am just starting using a Thingy:52 and want to use it with a C# UWP app. So far I have been able to retrieve the service and characteristics UUID's without issue but I am...
SDK 15.0.0 nrf52810 Example: Eddystone Beconing mode - ble_app_eddystone SEGGER Embedded Studio for ARM v4.12
I am using ble_app_eddystone example to advertise data in eddystone...
