Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I would really like to use Bluefruit and make a Long Range connection between Servers and my Central. I know that it is not build in Bluefruit by default, but there must be...
Hello!
I'm using BLE Mesh sensor client receiving messages sent from multiple sensor servers. I used 2 nRF54l15DKs as 2 sensor servers, each sending 9 16-bit float data...
I have a problem with connecting to my device after i disconnect from it. I have tried ubond function, it does not work. This is my disconnect function:
I have a service...
Hello Nordic support,
My application is based on nRF5 SDK for Thread and Zigbee v4.2.0, with Softdevice S140 as I want my application to operate in either in BLE or Zigbee...
I'm trying to setup an SPI communication between an EVK of the Intan RHD2216 and the nRF 52840.
Browsing similar issues, I read the following topics already
I apparently...
I've been using the following SPI1M pins and they've been working:
But I have migrate away from these pins due to production PCB layout problems. The pins I need to...
I'm using nRF Connect SDK v2.7.0 with v2.7.0 toolchain to program a device with nRF52840 SoC.
When configuring task watchdog timer with hardware fallback an assertion fails...
Hello,
I'm exploring the possibilities of implementing the Nordic UART Service but am having trouble understanding its security functionalities. I have a few questions:...
When I build the system using system default, use save minimum configuration，The chip-related configuration is also saved to my application configuration prj.conf, which it...
Hi , We as a Budding Tech startup are developing a Product With NRF5340-CLAA chip. We made the design referring the Datasheet and Reference designs provided by Nordic Semiconductor...
Hello,
I've been trying to modify the v2.4.0 Serial LTE Modem application sample for my nRF-9160 custom board, in order for it to communicate with our external MCU through...
Hello,
I'm currently running into issues when using the Logging Interface with USB CDC ACM. I tried to combine the cdc_acm sample and the console sample into one application...
Hello,
I measured the DC resistance between the RF output pin and ground pin and got around ~3-4 Ohm with digital voltage meter. This seems low. Am I missing something?...
Hi,
I have two nRF52833 DKs and both of them has connected to nRF21540 EK. I set the transmitter sending out 244 bytes data without stopping and measure it's current. The...
