Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi,
I was using nRF products a while ago, and now coming back to the platform again. However, it looks like everything has been changed with the nRF connect.
Anyway, I...
Hello all!
Because of very strict space requirements, we plan to use two batteries of the type ICP621333HPMT, connected in parallel and in combination with the nPM1300....
Dear Support Team,
In the project, I'm working on thingy91:nrf9160 board. Our test case scenario is to connect to cellular network(NB-IoT) and acquire GPS fix for which...
Hi,
I am using the PPK2 to evaluate the nRF5340. Neither of these devices is currently working properly, I think the underlying cause has something to do with USB that's...
Hello, I am using SES ARM V7.32 and SDK is 17.1.0.
I am trying to test the ble_app_uart example, but Build failed keeps occurring.
There are no other error comments, so...
Hi Everyone,
I am trying to develop a simple application with the XIAO BLE Sense device, the idea is to send a BLE message when something hits the device. To achieve this...
Hello All,
I am using the nRF54L15-DK and the nRF Connect SDK v2.8.0 with the Zigbee-Addon.
Is the maximum TxPower value that can be set for Zigbee 8 dBm?
Best regards...
Hello.
I am developing using nRF5340DK and nRF Connect SDK v2.9.0. I am checking the operation of "Scheduler Server". The action was executed, and the date and time are...
Hello. Using the Zigbee messaging cluster, we are writing code for data exchange between ZR and ZED. (Based on the Zigbee example light_bulb/light_switch/light_coordinator...
Hello,
I have a custom board which has an nrf5340 on it. We are using nRF Connect/Zephyr in this project. Currently the board has a pretty simple interface seen in my overlay...
I am currently developing a PC application for Bluetooth data reception and chart display. I want to perform secondary development on pc-nrfconnect-ble. My current development...
I'm using SDK15.3 on an nRF52840 with FreeRTOS and specifically non-preemptive scheduling.
I want to so some transfers on SPIM (it's configure with DMA but that's not a...
My project uses a PDM microphone connected to a nrf5340. I previousy had this working using the nrfx_pdm driver, with NCS 2.6 but then had to migrate the project to NCS 2...
There is usually a panel for application where you can see / delete or add build configurations, as shown in the enclosed picture. The panel on my vs code installation has...
