I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
I am following the cellular IoT fundamental course with nRF9151-DK.
I didn't have any issue until Lesson 7, but I found that the screen shot of the lesson is...
Hi devzone,
I am starting to write some tests for my application, and I have a couple questions/remarks about the provided Docker image. Link to documentation .
1/ The...
I have done a clean install of the SDK on Debian 13
I have nrfutil install and its working fine - i have tried installing both the v3.2.1 and v3.2.0 toolchains and in both...
Hello Nordic team,
We are using the GRTC on the nRF54L15 , and we are observing the following behavior:
When MCUboot is enabled , the GRTC (likely backed by SYSCOUNTER...
Hi, I am using nrf9151 as a modem running SLM. When SLM comes up, it throws this error. This is a new board run and 50% of the boards show this issue.
I appreciate there...
I am looking for a pairing between Windows laptop or Android mobile on the transmitter side and hearing aid which has bluetooth streaming features as a receiver..
I am looking...
Hi there,
Is it possible to have the DECT NR+ modem trigger events via DPPI? For instance, I'd like to capture a Timer value *exactly* when nrf_modem_dect_phy_time_get...
Hell ,
I am planing to use nRF52810 for one of my mesh application,now query is
How much power consumption its will take when RF is disable and listening only external...
Hi
We use nRF5340, set GPIOs as PDM for DMIC device, and measure waveform as below
The PDM DATA high level will decrease periodically
Is this waveform normal? If yes...
Hi,
I know that pc-ble-driver-py is archived but as there is no real alternative to it, I'm still using this package...
I'm using BLE nRF52840 dongle to connect to...
I am using the nrf52833 with 17.1 SDK and s140_nrf52_7.2.0_softdevice，i want to scan a scannable extend adv packets，
This is what i get in the BLE_GAP_EVT_ADV_REPORT ： ...
# Background
I am attempting to install ble-sniffer onto WireShark for BLE sniffing. I have been following the guide in Link. I have already flashed my nRF52840 USB dongle...
Using Thingy:53, I needed to add the following code to the boards/thingy53_nrf5340_cpuapp_ns.overlay file in order to be able to view the output:
&uart0 {
status="okay...
Hi
We measure I2C SCL falling time is 5.87ns, little faster than spec. 6.54ns ( 20*1.8/5.5)
We use PIN_CNF[n] (Address offset: 0x200 + (n × 0x4)) ID D drive to tune, but...
