I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
New project using Nordic platform and I need to send multiple commands (32bit fixed size) to a device quickly using SPI with the CS toggling between each. I just want to confirm...
Hi Nordic Team,
I am currently developing a commercial product using the nRF Connect SDK (NCS) . The system consists of several nRF52 peripherals and a PC-based application...
On the nRF9151dk, the transmission line coming from the nRF9151 starts with a 0.1 mm trace width and a 0.46 mm gap, which corresponds to a 50 Ω characteristic impedance. However...
Hi,
using nrf connect SDK v3.1.1
using nrf54L15 development board.
I am trying to run a simple button event yet callback is not fired when
CONFIG_PM_DEVICE_RUNTIME...
Hi
Could you provide nPM1300 NTC pin inside structure?(pull up resistor value, pull up voltage, others..)
And I want to know how to calculated NTC temperature by measured...
Hello everyone,
We'd like to use the rom_report and ram_report commands to be able to see (with a somewhat granularity) how much ROM and RAM do specific feature use so that...
Hi,
Question on the nRF7002. Can it be used as a hotspot to support 5 -10 wifi clients?
Basically, the need may be to download user manuals on site with a tablet.
...
Description
I was following the tutorial from DevAcademy regarding the setup of the nRF Sniffer for Bluetooth LE : DevAcademy: nRF Sniffer for Bluetooth LE
However, the...
Hello,
I designed a PCB using nRF52840 for controlling the board.
I have physical access to the following pins : SWDIO, SWDCLK , VSS , VDD , nRESET.
What is the boot...
Hello,
I am trying to exchange data with an external slave sensor via SPIM communication using the nRF5340DK.
I am currently facing two main issues:
1. The spi_transceive...
I am using the NRF54L05.When I was using the timer function of the Zephyr software, I created a timer with a 10ms cycle. After my system had been running for a long time ...
ncs: v3.2.0
chip: nRF54L15
If I set CONFIG_PM_PARTITION_SIZE_MCUBOOT=0x10000 (64K), MCUboot fails to boot, and the error displayed is: 'Protect mcuboot flash failed...
Hi,
Can you please guide me if I want to receive a larger message of around 15KB from server, how can I do it using CoAP block transfer in thread.
I am using nRF5 SDK...
Hi,
I built the nrf/samples/bluetooth/hci_lpuart program in SDK v3.1.1. I am using an nRF9160DK board version 1.1.0. I did add several printk statements to zephyr/samples...
