I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Dear Nordic Team, I would like to consult you about that, is there any way to flash modem shell to the custom PCB which already has nRF Cloud connection for location application...
Hi,
1.
I've been trying to get the lte_ble_gateway / let_sensor_gateway example wroking on the nrf9160dk v1.1.3. The example keeps failing at the No HCI driver msg. I...
Hi,
1. Check whether the nRF7000 supports setting the Radio test sample to Non-signaling mode TX test setup for packet generation
https://docs.nordicsemi.com/bundle/nan_046...
HI guys, I'm trying to figure out whether the problem I'm having is a hardware or software issue.
So, my problem is: I have created a custom board using the nrf5340 and...
We are facing strange issue we have this board https://www.raytac.com/product/ins.php?index_id=47
whenever we flash any firmware it works fine but if we erase from vs code...
I've made this following code with inspiration from the at_monitor example to test a custom board using the nrf9160 sip.
I get the following output:
When testing on...
Hi,
nAN_038 WLCSP Handling Guidelines V1.0.pdf does not support nRF52820 WLCSP
Please provide the WLCSP SMT data corresponding to nRF52820
Kind regards, Peter.Min
hello Nordic
i am working with two nrf52832 socs, with ncs v2.9.0.
I would like to know how many retransmissions occurred during a Connection Event in which specific NUS...
Hello,
I have a Xiao seeed nrf52840 and want to operate a peripheral IC over I2C. It doesnt have a driver so I'm following the developer academy on how to do raw I2C communication...
Hello, I am using the nRF Connect SDK v2.9.0. While working on the nRF52840 board, I used the library zephyr/crypto/crypto.h to perform AES/ECB encryption.
Part of the code...
Hi guys,
I'm a bit frustrated with the NRF Power Profiler II. I'm working on a low power project with the NRF52832 with a custom PCB and I decided to buy this power profiler...
Problem Description
I've implemented a W5500 Ethernet controller emulation for NRF7002 modules. While UDP socket sending works correctly, receiving UDP packets is problematic...
Hello there,
I was going through the Wifi fundamentals courses lessons in nordic academy and was using ncs 2.4 version, I was able to give it a build for one example,...
Hello,
I have gone through many devzone threads which suggest that Ble Mesh over coded PHY is not officially supported but, is possible. I am trying out the "Mesh" sample...
