Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
I've been playing around with some code that puts my hardware into System OFF mode to save power, and then will exit this mode and start up when one of three different GPIO...
Hi,
https://github.com/NordicPlayground/nrf52-ble-app-uart-c-multilink
I have tried the example you modified. It works fine. However, I get ERROR 17 NRF_BUSY when 2-3...
Excited to have ordered my BLE Audio DK which uses NRF5340.
In my use case I am looking for many microphones (audio transmitters) to a single listening device (audio receiver...
Hello!
I am working on a medical device project utilizing nrf52832 microcontroller. We use a mobile app to control and interact with the device through BLE since the device...
Basic Bluetooth connection question
How do advertisements usually work? So I have earbuds and a phone. When I pull the earbuds out of the case they auto connect to a bonded...
Hi All!
I am using nrf52820/33 and am able to successfully connectable advertise (coded PHY) by nrf5 SDK. Now I want to use NCS (Zephyr RTOS) to do the same job . Can...
Hi! I'm trying to use the nRF Connect App on a M1 Mac. I keep getting the error shown above with my Jlink connected.
This is the output of the nrfjprog cli tool:
How can...
Hello,
I have been experimenting with the direction_finding_peripheral sample in the nRF Connect SDK. I have been trying to connect to the peripheral using a custom device...
Hi, I'm working with nRF52832 and S132 v6.1.1 on SDK15.3.0. I'm using two nRF52832: one is scanning (active scanning) and one is advertising, and I want to exchange data between...
Hello everyone,
I am developing an application, with the nRF52840 chip (actually BMD-380 ) , that streams via BLE data read by an SPI sensor (ADS1293) to an Ubuntu machine...
I use the LED onoff example of the Nordic BLE Mesh template (Version : 5.0), using two nodes (One Client, One Server). The nodes are already Provisioned.
I want to know...
We have a requirement of sending data to nrf mesh app without provisioning. So Can we use health server model to send data on app without provisioning?
The reason we choose...
My understanding is that the Modem Library is a dedicated interface to the internal modem in the nRF9160.
We also need a 2nd modem interface to an external device that also...
Hi
We are developing a system based on nrf desktop application of nRF Connect SDK 1.90. There are 4 devices in this system: a dongle, a central device and two peripheral...
Hello Nordic Team,
From the below link and few other sources
nRF52840 SDK16 - BLE Descriptors and Notifications - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi...
