Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
Hello Devzone,
I'm in the development stages on a battery based sensor device, utilizing nRF9160 System in Package for LTE-M connectivity and application processor. I have...
Hello Everyone,
We are using a nRF52810.
We have ran into an issue where our 32MHz XTAL can take longer than 400us and thus the Errata 3.6[68] CLOCK: EVENTS_HFCLKSTARTED...
Hello all!
I would like to use the PWM driver, yes, the hardware that is on board the chip. To get going certain code parts from the PWM driver that comes with the SDK,...
I would like to set the radio channel using 'uint32_t nrf_esb_set_rf_channel ( uint32_t channel ) '.
In 'nRF52840 Product Specification v1.7', '6.20.12.2 Operating frequencies...
Hello !
1.
In nRF21540 PS current consumption in TX mode is specified like this :
TX_20dBm State: TX POUT = 20 dBm 110 mA
But it is not clear if it depends from actual...
Hello everyone,
I am working with the SDK v17.1.0 with the DK nRF52832 with the examples of ble_app_uart and ble_app_uart_c.
I want to send an array "data_array" of uint8_t...
Hi,
the tool chain of NCS1.9.0 is at /opt/nordic/ncs/v1.9.0/toolchain
I just install NCS2.0.0 by NRF Connect Desktop.
However, I found there is no "toolchain" in /opt...
Hi,
We need help in getting an system call / API in Zephyr which updates the consumption of memory ram and flash
can you please suggest any mechanism which verifies...
I am using nRFConnect on windows 10 with the nRF540 Dongle for the first time.
I am successfully able to connect and view parameters on the nRF52832 using the Dongle.
...
Hello,
In my project i am using nr52840 actually its a custom board and i want to send the sensor data to custom app sometimes data updating and sometimes data not updating...
I am try to flash BLE SDK binary by Nordic, but using --sectorerase --verify with --reset seems to fail :
Two options combined :
I'm using the nRF51 SDK version 17...
Hi
I am developing for the nrf52832, S132, SDK17, trying to set up a SAADC multiple channel scan, however at times I will wish to only sample one channel, specifically ...
nRF Connect for Desktop 3.11.1, Programmer v.3.0.0.
Message showing with Jlink I am using and device connected:
13:58:12.602 Using nrf-device-lib-js version: 0.4.11...
