the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello! I have WF200 wi-fi chip connected to the nrf52840 through SPI. I configured bare-metal example code of WF200 chip to work with nrf-sdk and this example (basic CGI server...
No connection after disconnect with Android App Nordic Uart Service until mac-address of smartphone changes
Multilink multirole software developed in SES studio.
Other...
Hi I have a product that uses an Nrf52810 in a Raytec slave module. I am able to successfully send and receive packets of data using your UART app in the nrf Toolbox
I would...
Hi,
1. I need to change the total free space of this file system: Current size:24576 bytes
3. I made the following adjustment, but it didn't work.
4. How do I modify...
nRF Connect for Desktop cannot find any devices from the SELECT DEVICE tab in LTE Link monitor or Bluetooth Low Energy app.
The device can be found on Device Manager and...
Hi, all.
I'm using nRF52833 and trying to communicate ESP8266 using UART.
I already successfully communicate with Dust Sensor with baudrate 9600, so I tried to communicate...
Hi,
I'm trying to find an example of using the I2S audio interface with the Zephyr RTOS on the nRF52840dk_nRF52840 development board or on an nRF52840 device in general...
Hello ! I'm a beginner here, and I have a problem that I struggle to solve. A few years ago, a firmware was done by a company, for the one I work for. It was done with IAR...
Hi,
I am toggling a GPIO using the below code and trying to find out the relation of the frequency and the code statements. I know that GPIO peripheral is running at 16MHz...
Hi,
after fixing a missing ground in my setup (see devzone.nordicsemi.com/.../interaction-jlink-and-power-profiler-ppkii) I have not been able to get less than 50uA of idle...
My B0n bootloader (running on the network core) is trying to access XIP space and faulting. This is a part of an network core upgrade.
From what I can learn from the data...
Good evening,
I’m testing the SDK v17.1.0 “Open Bootloader with DFU” example. I’m using Segger Embedded Studio to program my Nano 33 BLE via the debug interface (P20) of...
Hello again Nordic World!
Yet another question about getting RSSI values:
Again, using 10028 and 10040 boards under sdk 12.3.
Is the adc acquisition of rssi done synchronously...
Dear DevZone,
within out project we make use of an esb communication between a nrf52840 DK connected to the PC via USB (a "station"), and a custom PCB with a nrf52840 micro...
Hi all,
We are developing an application using nRF52840 device and the idea is to enable the device with peripheral and central roles.
We would like to set two advertising...
