nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I am using nRF52840-DK as a BLE sniffer. I have set up Wireshark to sniff the packets. Between c entral and Peripheral, there is an authenticated LE secure encrypted BLE connection...
Hi,
I'm working with a modified version of the secure bootloader included in the nRF5 SDK 17.0.0. I'm using an nRF52832 to update an STM32 over the air.
I have two update...
Hi all, I need to use the nRF5340's SPIM4 peripheral for 32 Mbps communication. I see dedicated device's pins are pre-assigned on nRF5340 for SPIM4, ad I want to use these...
We have an nRF52840 connected to a SAM4e over SPI. The nRF52840 is the slave and the SAM4e is the master. The 52840 uses a SPI slave routine based on the SDK17 SPIS example...
Hi there,
When parsing the GPS data from the Thingy91's GPGGA format, I've received invalid from such parsers.
Invalid:
I'm still able to successfully parse the value...
Hi,
We used modem fw 1.2.3 ncs 1.3.0 before and got upto 8 satellites when searching for a fix.
Using latest modem firmware 1.3.0 + ncs 1.5.1 we see no more than 3 satellites...
Hi,
I'm using the nrf52 mesh sdk v5 to make a provisioner based on the provisioner example of the mesh sdk.
During some provisioning, the provisioning process timeout...
Hi
in communication networks, GPS is often us to sync network elements and to get accurate timing.
with nRF9160 MFW 1.3, "GPS time based configurable IO-pin / pulse" is...
Hi!
I am developing an application that starts and stops gps occasionally. I am running the gps in GPS_NAV_MODE_PERIODIC with a timeout of 100s and an interval of 240s....
Hi,
We are having problems with nRF52840 dongle.
Intermittently pc-ble-driver-py throws the error in the subject when trying to open interface to nRF52840 dongle. After...
I got an average DRx power consumption of 415.03 µA for 2.56s in the Online Power Profiler for LTE. But unable to get the average power consumption of eDRx.
In the following...
Dear Community, I'm trying to use both datasheet-announced I2C interfaces, one as slave and one as master. Datasheet: www.mouser.de/.../BlueNor_BM833A_datasheets-1627946.pdf...
I have a BLE central application (a form of BLE to LTE bridge) which I have no choice but to redesign due to the dismal state of the supply chain. The original device which...
Is there a release plan in place for the release of a pc-ble-driver-py version that supports Python 3.9? I can see on the github that the support has been integrated into...
Hello,
We recently implemented DFU on Android for nRF51 and nRF52 devices using the Android DFU library from GitHub. It works great, and we would like to see if it is possible...
