Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
We have ported from SDK v15 to v15.3 but now have a problem getting the USBD to start.
Below is a sort of pseudo-copy of our USB init routine which is working for us on...
Hi,
On Nordic SDk 15.0, I have observed that USB CDC ACM Example is not working in interrupt mode on nrf52840 Evaluation kit.
But I have tested USB CDC ACM Example in...
I'm experimenting with nRF52840 DK
However, using break points in the main loop causes 'app_error_fault_handler'.
using the iar compiler. What's the cause?
Hi~
I have a question about the SAADC.BLE Connect Mode. When I turned on Saadc LP mode, the power dissipation was 0.02mA for single-channel sampling, but 0.5mA for dual...
Hi All,
I have looked through the devzone and cannot find a solution to this. I am using the nRF52832 SDK 15.2. Working with a BNO080 IMU over TWI.
I need to read more...
I have bought new thingy 91 from mouser. Com. I burnt the latest pre complied hex file for assist tracker. I am getting all data except gps.
it is not getting connected...
I have a custom firmware developed on a nrf52832 SoC. I would like to know if i could see nrf logs such as nrf_log_info and nrf_log_debug via bluetooth? if this is possible...
Hi!
I want to use a TensorFlow Lite for microcontrollers model in my existing project built on top of the nRF5 SDK. However, as outlined in the nrf-tensorflow example ,...
Hi ,
I has been using NRF9160's AT client mode to connect with CMW500, however I found some problem.
The following is the command log that I used to send via UART. However...
I'm working on code that needs to discover services on the central so I'm using ble_db_discovery_start. However, I notice that if the connection handle passed into this does...
I am trying to measure frequency of a gpio pin. I am using the code from the below thread -
https://devzone.nordicsemi.com/f/nordic-q-a/9036/measuring-input-gpio-pin-frequency...
Hello,
About 2 months ago I upgraded my project to SDK 17.0.0 (from SDK 15.0.0).
When I opened the datasheet recently I found that a newer version - SDK 17.0.2 is now...
Hello,
Im trying to implement FOTA on the nrf9160. Currently my first version is working however I would like to decrease the amount of data used in the process. According...
Edited: It appears any use of NRF_CRYPTO_BACKEND_CC310_BL breaks joining.
Environment: nRF52840; SES; nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b
I am implementing Thread...
Hi Support Team,
For the recent DFU issue "some Android 10 can not connect to the device during the DFU" ( https://github.com/NordicSemiconductor/Android-DFU-Library/issues...
