Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hello,
I'm trying to set up auto-provisioning and onboarding in my project as described in this sample: https://github.com/nrfconnect/sdk-nrf/blob/066ac6f61fe19ad91d805fd788d782e245f09a2e...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
On nRF5340 with external flash (SDK 3.2.x), is it possible to both support serial recovery enabled for both cores while supporting simultaneous DFU?
It seems like...
Hi,
i am developing under ncs 3.2.3 (then toolcahin 3.2.3 -> nrfutil-device 2.17.1).
FLashig OTP registers using batch method, i am getting the following "error" on nrf54l15dk...
Reference: first consult as Case id. 305571 Replyed by Tobjorn
I have a working proyect in wich 485 cable communication was replaced with NRF24L01+ but I need some help...
In the enqueue function esb_write_payload , the enqueue implementation uses ++tx_fifo.back .
In the dequeue function esb_pop_tx , the dequeue processing also uses ++tx_fifo...
I'm working on a project where we're planning to use XIAO BLEs on an OpenThread network, for that we need very low power consumption. I've been trying samples to get low consumption...
Hello, I have followed the guide to do a serial recovery of the appcore and it's working fine. Now I would like to be able to update both the appcore and the netcore. I have...
Hi, I have developed a firmware in which I have added the custom service. My custom service UUID is showing 00001400-0000-0000-0000-00000000fff0 but I want only 0xFFF0. I...
The title says it all. Code to reproduce:
Put this at the very first thing in main() in e.g. the cellular/udp sample (configured to use nrf9160dk/nrf9160/ns with the...
I am getting issue in building the network core hex file for BLE. I am performing peripheral NUS example with MTU 247 max payload with data length extention. But I am getting...
Running Zephyr + NRF54l15 (board = nrf54l15dk/nrf54l15/cpuapp)
When attempting to use gpio1.5 and gpio1.4 for ADC inputs, we first disable the UART20 (which uses those pines...
Device: nRF54L15 (CRACEN + KMU)
SDK: nRF Connect SDK v3.2.1
Hi Team,
I have a question regarding storing ECDH key agreement material in KMU and using it for HKDF-SHA256...
Hi,
I'm developing an application with an nRF54L15 on a custom PCB and I'm looking to minimize the current consumption. The application is very simple, just a sensor that...
nRF54L15 SDK:v3.1.0
Hello, I have implemented the FOTA function according to the official documentation. Now, I would like to add a switch for enabling and disabling FOTA...
