I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
Hello guys,
I wanted try run on NRF9160 hardware CC310 cryptographic module.
I installed all software and tried run secure_services demo. Thats works, cool!
In next...
Hi,
I am using SDK 15.2 and Softdevice S132 6.1.1. I'm having an issue getting my custom hardware built around the Laird BL652 (nRF52832) to start the program. It always...
Hi.
I need PC app communicate with my development board though BLE.
so I'm testing pca10059 with ble-pc-driver sdk.
I tested ble_app_att_mtu_throughput example with...
Hey, I am trying to sample from 10 analog sensors and stream the results via bluetooth. Since the nRF5 is on a board that only lets me access 5 Pins, I am using a 16:1 multiplexer...
Hi everyone!
At the begining I want to write what I'm using to make everything easier.
Device:
- NRF51822 xxAC ( This one ). - GSM module Simcom Sim 7000E ( This one...
I need to be able to upload my application to an nRF52832 through an ARM architecture Linux machine that I have remote access to. nrfjprog is not available for machines with...
Hello. I connected the Image transfer service (running on a nrf52840) to another nrf52840 running a modified BLE_NUS_C service.
However, a BLE packet won't be send out,...
Hello,
I have the following issue when trying to detect which GPIO triggered the interrupt:
For my low power application, I was trying to connect two switches to the...
Hi,
I'm in the process of designing my first prototype with the nRF9160 SiP. For the LTE antenna sub-circuit, I simply want to replicate (as much as possible) Nordic's reference...
Hello,
I am using custom nrf52832 PCB as central role. Also i have the peripheral with similar board . Peripheral communication is working properly if connected with the...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
Similar to WiFi and 802.15.4 where there are...
Hello,
Customer want to use
nRF51822 Bluetooth Smart Beacon Kit
with this requirements:
We need the most simple beacon. Additional sensors are not needed. Its main...
Hello Nordic team,
I'm using nrf52840 DK with SDK 15.3.0.
So I had an example sending data similarely to the ble_app_uart_c example that worked OK.
Basically I have...
Hello there!
We have a running prototype with an NRF24L01+ and ESB. But since it is not recommended for new designs, is there a successor for this setup?
Very low latency...
