Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
I have been experience that the if the device under a DFU process reports the error BUSY, because the external flash on the device is used for fileaccess the DFU process from...
Hi nordic support:
Our product uses the nRF9151 and prepare for GCF certification testing , which need to capturing LTE mode trace log .
We first intend to try running...
Hello everyone,
We are currently working on a project that uses the nPM2100 to power an nRF52840. Our application requires automatic enabling break-to-wake mode each time...
Hello DevZone,
One customer used Timer+PPI+GPIOTE to simulate an UART. Now it works fine.
However, when there is other timer's interrupt, the simulated UART may lose some...
Hi, I just received our nRF54LM20DK, and am trying to get a functioning BLE sample on the board. Many samples are supported, however I have not gotten a single one to work...
Hi,
I have a question about SPIM. Is it possible to have two events via DPPI that will start different SPIM transfers for the same SPIM channel?
What would happen if a...
I have the board: NRF52840-DK PCA10056 3.0.3 2026.5 1050266921
Is it possible to use OB J-Link to debug STM32/RP2040 MCUs connected to P19/P20? Or OB J-Link support limited...
Hello, My nRF54L15-DK has suddenly stopped working, and it appears to have a hardware-level power failure.
The board was working normally the previous day while running...
We are using CMakePresets.json extensively in our project and rely on the condition field to control which presets are visible depending on the host system.
However, it...
Hello,
We are using the nRF52840 with SDK 17.1.0, SoftDevice S140 v7.2.0, and the secure bootloader (nrf_bootloader.c).
Our application relies on reading NRF_POWER->RESETREAS...
Hi there,
One of the functions of the DECT MAC layer is to allocate radio resources to RDs. According to the standard, the MAC layer does that using special beacon messages...
Hi,
I'm working on a wireless sensing project using the nRF54L15-DK (PCA10156) where I need continuous RSSI measurements at 2440 MHz. I'm accessing the RADIO peripheral...
Hi,
I am working on an nRF52832 using nRF5 SDK 16.0 and I am seeing inconsistent behaviour in the RESETREAS register. During a power-on reset, the value is usually 0 but...
Hi!
We are building an application for Thingy91X and noticed that there is an overlap between the shared memory between the app and net mcus, sram0_shared, and RetainedMem...
