Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
Hi,
Asset tracking example used to work for me, after reinstalling my environment I get nrf_cloud_connect failed: -111
this is the output from the LTE link monitor:
...
Hello,
I'm using the same SDK used on the Thingy:52, compiling with GCC. I'm using the Rigado BMD-350-A which uses the nrf52832.
I'd like to use P0.09 and P0.10 as GPIO...
I have three buttons connected to pins PO.07, PO.08, PO.09 on my card. I changed the pin assignment and for the first two I have no problem using them as buttons, but I can...
Hi there,
I've been trying to figure this one out for a day or so now with no luck.
I'm successfully able to build and program using Segger Embedded Studio, but I would...
Hi
I am new to nrf52840. I am trying to communicate on I2C bus with Cypress semiconductor CY8CMBR3116 capacitive touch IC. Some how I am able to connect the on I2C bus...
Hello,
I'm developing a custom application based on SDK 15.2 on nRF52 using softdevice S132 v6.1.
In my development, I want to ensure timestamp synchronization between...
Hi,
I am using NRF52 SDK 15.3 on nrf52840 Preview DK
I am using BLE to transmit data, I want to use PPI to get readings off of SAADC but using 'app timer' instead of TIMER...
I'm currently on a question for which the documentation here can't help me.
If I'm correct, the Dual-Bank Update allows to retain a safe copy of the old firmware image...
Hi,
I am using esb project of SDK15.3 to test esb PTX and PRX function.
The default setting of address-0 and address-1 is 0xE7E7E7E7 and 0xC2C2C2C2, and PTX and PRX can...
Hi,
1.I want to develop the my product using nrf51822 with PCB antenna(as shape given in sdk hardware) with following board stackup-
2. i am going to use cap-0603 in...
Hi,
I am using nrf52840 S140 PCA10056 SDK 15.2.0 version with example ble_app_multirole_lesc_S140_PCA10056 . i am using Segger Embedded studio IDE. So now problemis i am...
Hi,
I am trying to get my systemOFF current below 1uA, but Im struggeling.
normally I use MBED, but to eliminate that variable, I just did a test without MBED, I took...
Hello together, I am experiencing problems with the nrf52840. I got the BLE_APP_Blinky example to run. Now I am trying to get the BLE_THROUGHPUT example experiment to run...
Dear nordic,
I want to know something regarding your SDK. I have nrf52832 development board and i use sdk 15.2 .
1. if i want to use BLE 4.2 version what changes i want...
Hi,
I am working on a project where my mobile phone will be acting as a central device and nRF52840 DK will be acting as a peripheral device. I added the UART example to...
