I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Dear nordic,
I started to integrate PCF853(RTC module) using i2c. but its not getting proper output can you help me what wrong i do?
slave address:- 0x51
read register...
Hi Sir
I enabled the "APP_UART_FLOW_CONTROL_ENABLED", but I measured the CTS / RTS pin always is low during data transmission.
Is it normal ? How to check UART FLOW control...
Hey, i have got UART work on my Thingy52 with ANA/DIG0 and ANA/DIG1 as receiver and transmitter but when I am trying to use EXT0 and EXT1 as receiver and transmitter it doesn...
Hi,
I am new to embedded device development and I am wondering if I could get some help on SPI control from nrf51422/51822 chip with dev kit to AD9837 wave generator. I...
Hi,
I am try to create a PWM output which can move the specified number of steps.
Please find following source code
After I execute above problem, I can get following...
Respected sir,
There is added external reset button at SRU532 module, and changes are given according to it using wakeup button at code.When wakeup button is used then some...
Hi all,
I am trying to implement a multilink central with UART. I had looked through the forum on all discussions in about this and followed this thread to come up with...
Hi guys,
I'm testing the 52810 duf function.
hardwar: 52810
using SDK: 15.3.0
softdevice: s112_nrf52_6.1.1_softdevice.hex
download software: nrfgo Studio
bootloader...
I am trying to flash the blink example from SDK v15 into my custom nrf52840 board, I am using pc10056 example.
I connected my ulink2 to swdio, swclck, gnd and vcc of my...
Hi,
Since the last update of the 'Getting Started Assistant' (0.9.0) from 'nRF Connect' 2.6.2 on Windows, I can´t set up or compile any sample of the SDK for the evaluation...
So I've been having a problem the last few days - using the NRF52832 we have an SPI chip connected his chip requires a clock signal (1MHz) that is being generated by the NRF...
We have written code based on SDK V12.2 and found it doesn't support power saving mode. Given that it's very complicated to transplant to higher version, how can we fix the...
Hi,
I want to interface two QENC with nrf52840, I saw QDEC example and it works as expected.
The problem I am facing is that QENC has four pins of which two are for power...
Hello,
I am having strange issue. I'm getting some data from custom service and characteristic. I can see the data being received is correct. However, if I try to pass the...
Is there a set date for the release of a tracker SW with working GPS? And secondly, will there be a step by step instruction how to upgrade the software on the dev. board...
