Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
I have the same problem as how to discovery 128bit characteristic UUID which is totally different form 128bit service UUID ，the uuid in this question is the same with me,but...
I have added ANCS related functions to my project, but sometimes I get some errors. The error message is as follows: Error: Parameter does not refer to an existing object...
Hi,
I want to change value of serial number after dis init, I want to use sd_ble_gatts_value_set to set the new value, but I dnot know what is the right connection handle...
Hi
I try to flash the firmware from project light_switch_server_nrf52840_xxAA_s140_6_1_0 to nRF52840 dongle to build the Mesh Network with below modifications:-
Use...
I set the Thread network with 2 Dev Kits. I tested it using CLI directly. The network works.
But I can't observe topology on the monitor tool.
Reproduce path:
Follow...
Ive been working on this for some time and can not get two boards successfully communicating using the 125Kbps on the NRF52840. I am simply having one chip transmit advertising...
HI........ I am working on nRF MESH latest version , so i am here using three boards nRF52832 , i have set the character message in client side , when the button 1 is pressed...
Just continue my work on implementing LESC MITM on hear_rate_collector (Please check my development environment settings here as well).
Since sd_api_v6 on pc-ble-driver...
Developing IoT product using a module using Nordic nRF52832 - using their Shockburst protocol
Can ANYONE explain why we would need to be registered with the Bluetooth...
Hi,
I'm trying to make provision for AT command interface in my new nRF9160-SiP based design.
Couple of questions related to that:
1) Which UART (nRF9160-SiP pins) should...
HI,
Im using nRF5_SDK_15.3.0_59ac345 - SDK and two different bootloaders.
The first one is - sd_s140_bootloader_buttonless_with_setting_page_dfu_secure_ble_debug_without_bonds...
Hi,
I notice my dfu bootloader oversized after I merge softblink led feature into the example code. How can I modify the linker_section_placement_macros and the linker_section_placements_segments...
Hello,
Working on MAC. High Sierra.
got a 52840 dongle (but also a thingy and a devkit following the latest conference)
Trying to start at the beginning and build...
Hi,
currently I am trying to figure out how to disable the cryptocell hardware after enabling it, because if I enable it and then enter systemOFF, the system still draws...
Hello,
I am using NRF52840 Preview DK, I am running peripheral/SAADC example on the board, I shorted Channel 0 and GND on the board and I am receiving negative values...
