I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hi,
I am using 2 gpio interrupts from 2 separate sensors with active soft device. one sensor generates interrupts at around 400-800 ms and the other comparatively lesser...
Hi,
So I am trying to poll the signal strength of the nRF9160 DK and at first everything seems okay, the device gains connection and all the boxes in the LTE Link Monitor...
We have added Nordic Uart Service (NUS) into the nRF mesh code and we created two mobile application.
First mobile application:
- is for nRF mesh provisioning which is...
Hi,
The datasheet for the antenna used in the dev kit, P822601, has its specification performance measured on a PCB DUT at 140 x 50 mm^2 - which seems rather unnecessary...
HI !
i have a problem during importing nrf9160 project in SES , knowing that i imported this project and others with same toolchain installed and other requirement.
onetime...
hi all
i have been working on a raspberry pi hat design and i would like feedback on it's design
this is the link to the github repo and i do update it regularly https...
hi,everyone
I want to run the DFU example in meshV3.1.0 . but i still can't understader how to run it . below is my understanding:
1.ther are must have 2 devices , A device...
Hey, i having problems with uploading code to my Thingy52.
Equipment that i using: nRF DK https://www.nordicsemi.com/Software-and-Tools/Development-Kits/nRF52-DK Nordic...
Having issue with nrf52840 interface with sim808 for GPRS connection. I am trying to interface nrf52840 with sim808 using UART. But only AT and ATD command reply i can see...
Hi,
I am currently trying to test the capability of bluetooth 5 long range mode using a pair of SparkFun Pro nRF52840. I have used the blue-app-uart example and:
1)...
Hey
I am working on Bluetooth mesh. I am able to find the RSSI from server whenever i received the message from client in mesh(light switch example). Now I have to find...
We used NRF52832 to make a Bluetooth solution, but the customer wants the broadcast name of the product to be regular, and the MAC address also needs to follow a certain rule...
Hi
I have below requirement on NFC using SDK 12.3.0 and soft device S132. please suggest how to start with the same.
1.NFC operation. (Simple Read Write into NFC Tag Memory...
Hi,
I'm working on getting the DFU bootloader working and I'm following this blog post.
I'm successfully compiling and loading the bootloader to our custom hardware...
I want two pwm channel output 1MHZ frequency, the phase difference between two PWM channels is 180 degrees。when i set two pwm frequency to 500KHZ, use the configure below...
