Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Hi
Can anyone please explain me as how to change the start address of flash (while using soft device) and changing the start address of RAM too. I am working on nRF52840...
I'm looking at the patched version resulting from applying the pc-ble-driver patch, but this might be present in the original as well.
675 case APP_USBD_CDC_ACM_USER_EVT_RX_DONE...
Hello,
I'm trying to receive a 2-byte data from a sensor from Maxim Integrated MAX31875 but the nrf_drv_twi_rx function only receive 8 bits data. Does this function to receive...
I'm evaluating the NRF9160 DK, and have run into some interesting issues.
I find that the AT client works, sort of, though it's quite flaky and I quite often get timed out...
So, time to give back...
Updating this post ( https://devzone.nordicsemi.com/f/nordic-q-a/23488/a-nrf52-function-mapping-to-nrf51/124863?focus=true#92262 ) which outlines...
Hello
I am in a process of pre-manufacturing for NRF52832 and have a fully working application containing
softdevice: s132_nrf52_6.1.0
secure ble bootloader
application...
As i understood by reading the forum and documents, the maximum advertisement packet length is 31 bytes. That means that devices with custom UUIDs (128bit = 16bytes) may not...
Hi,
I am a hardware designer. I have little knowledge about firmware or software.
Now I want to apply the nRF52832 to an ultra-low power application as a beacon.
I...
I have recently ported my nRF52832 application from SDK 12.3 to SDK 14.2 and have been disappointed to find that the preripheral is locking up after a period in operation...
Hi,
My product have to pass SRRC certification,but the pre-test is fail. The certification lab need to test RF frequency at 2402MHz, 2441MHz and 2480MHz separately,and the...
I have a nRF9160 DK that I am trying to get on a network. The iBasis sim does not appear to be in the coverage area, the SIM activated, but has not had both LEDs 3 & 4 blinking...
Hi,
I have nRF9160-SICA Modules with me and I designed a custom board for them. I do not have the nRF9160 DK.
I want to know if there is any way to program nRF9160 using...
I have two TIMER instances, TIMER1 and TIMER2, both setup to Clear Mask on timeout (aka restart). I use TIMER1 and PPI to trigger ADC measurements every 5msec. In the ADC...
I've been documenting this issue and asking questions here:
Intermittent device reset in modified ble_app_beacon example
Since I need to post a proprietary schematic,...
Hello,
I was examining the power supply part of the Thingy and I noticed that the charging current is set to 0.5 C, wich is 720 mA (checking XR6804's datasheet it seems...
