Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
Hello, We planned use nRF52840 in our project, and I have some questions about this MCU. 1) Is it possible to process signal from 8-GPIO with frequency of request 32MHz? We...
Dear,
I am testing nRF9160 DK with iBasic SIM, FW: SecureBoot and AT Client
I am trying to send SMS to my phone. I see : https://devzone.nordicsemi.com/f/nordic-q-a...
Dear Sir,
I am working with
SDK --- nRF5_SDK_15.0.0_a53641a
softdevice -- s132
nrf52832.
I was working with example codes in the SDK folder.
I am working...
Hi,
I need some help calibrating my moisture sensor analog readings using 3.3V regulated power source (VDD = 3.3). Here is my set up, borrowed from the proximity example...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
I am working on an nRF52832 BLE peripheral prototype which sends bulk data to a central as bursts of large notifications. I am encountering an error where the connection gets...
We are manufacturing 2 types of gas sensors that communicate BT LE. One use an nRF52832 and the other an nRF51822. Will the nRF52 dongle communicate with both of these? Is...
Hello
I am currently programming with keiluVersion4.
Previously, I used "fatfs example" of SDK_15.0.0.
So trying to test the function of BLE, trying BLE communication...
Hi ,
I'm working on a 2.4GHz wireless microphone project now.
I want to make a scheme of two microphones transmitting to a single receiver(2T1R)。And ,i have tested this...
Hi, Andreas.
Following the guide you find in the document " Buttonless Secure DFU Service ", I get errors while trying to compile. In order to ascertain were is the problem...
How to realize the USB HID interface and PC data transmission?
I want to connect my computer via USB hid protocol for communication
This is my code, but can only send...
Hi everyone,
I am a beginner for BLE software development with MDK-LiteV 5.26.2.0.
Target device: nRF52832（EKSHCNZWZ made by Taiyo Yuden）
SDK: nrf5_SDK_15.2.0_9412b96...
I use the example from nrf51422 ble_app_uart_c with SDK_12.3.0 to connect via BLE to nrf52 usbd_ble_uart. When sending data that exceeds the length of one BLE packet (for...
I combined to examples from the examples library combining the sdk_config, source code, and adding references to the included files.
The application will not compile and...
