The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi,
I really would like to be able interface with the modem at the lowest possible level. I got the bsdlib working.
I use the following procedure to send AT commands and...
Hi Nordic,
We are having a Finger Wearable Unit(FWU) based on nRF52832.We are using JLINK Base Debugger to debug the FWU.We are able to debug and get the debug logs when...
Hi. I have built an ble application which runs on the nrf52832 with softdevice S132 V 6.0.0. In addition to the application and the softdevice I program a bootloader on the...
Hello,
I am learning bluetooth mesh with Light switch demo example. I have downloaded the folder "nRF5-SDK-for-Mesh-master" from the link "https://github.com/NordicSemiconductor...
Hello all!
We have custom HID with multitouch BLE device. We took HID descriptor from USB where this works pretty good, ported it to BLE and it seems not working as expected...
I just upgraded to nRF Sniffer V2.0
The Time column of Wireshark shows wrong values for short delta times. Is is set to "seconds to previous packet"
My advertiser runs...
Dears,
I have a problem with the ble_ant_app_hrm in the examples (multiprotocol). I am using a pca10040 demo board with sdk 14.2 with IDE SES on a MacOS
I have flash...
Hi, I'm using nRF52832 with SDK 15.2 and 3.0 (Mesh). when I try to provision 2 or 3 client/servers the nRF Mesh application behaving properly which means provisioning is happening...
Hello,
I would like to use an usb dongle with nRF52840 above and
- on bluetooth side give an spp or vsp profile
- on usb side be an usb cdc device
the reason is: I...
Hi,
We are currently implementing a mesh application that is expected to have a large number of mesh devices. We have already tested DFU on a smaller mesh and it is working...
trying to bring up the new nRF91 dk with default firmware.
Registered the eSIM. switch sequnce activated with LED 3 and 4 starts blinking. After that LED4 starts blinking...
Hi,
During provisioning of a device the Device Name is changed to the default "nRF5x" after completion of the PB-GATT connection. The name is later on changed back when...
Hi,
I am trying to use latest pc-ble-driver. The code is based on pc-ble-driver-js. When I call sd_ble_gap_scan_start(), I get only one "device discovered" event. This happens...
Hi, I need to use nrf52832 as HID keyboard and send function keys F1-F9 to computer. I have tired to run HID keyboard example in nrf5 SDK. How do I send function keys instead...
