I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Good afternoon,
I'm using nRF52840 with SDK15 and Softdevice6.0.0.
I'm using the Queued Write Service Module to make use of a characteristic able to receive up to 510bytes...
Please suggest a tool that can be used for monitoring and and analysis of Nordic's BLE packet transmission rate.
I would like to measure packet irregularities over time...
HI,
How to use sd_ble_opt_set() with the option BLE_GAP_OPT_SCAN_REQ_REPORT ? After setting this I can expect to get the event "BLE_GAP_EVT_SCAN_REQ_REPORT" with information...
Hi,Support Team
I Use the nRF51822 SOC for SDK12.3-example-DFU-bootloader_secure, when I Select the ZIP upadate file,it has a reminder "Loading file has failed. Try different...
Hi,
I use buttonless DFU with the secure bootloader.
When I push a button my application advertise in fast mode with an interval of 40ms and for 5s. After it return to...
SEGGER Embedded Studio Release 3.40 Build 2018052200.36079
The so-called "flash (sic?) placement" XML file contains two sections:
First:
which does, indeed, seem...
Hello, I am currently working on a nr52840 s140 Sdk 15.0 card and I want to recover data from a component running on the i²c bus. (I have not yet installed the component on...
Hello,
I would like to know if it is possible to use a nRF52840 as bridge between ethernet and 802.15.4/thread. For a sensor network I need an ip connection between multiple...
Hi,
I'm using nRF52 DK. I was checking the message sent by NRF_LOG_INFO() on Termite. I'm getting driver error when I try to connect to laptop's bluetooth.
Without the...
Hello
what is the maximum limit for PWM outputs pins on nrf52832? Can we use all the GPIO pins as a PWM output?
For ADC, i can see there are 8 dedicated pins , but i...
hello i am beginner in this,i am using example\ peripherals\ saadc for nrf 52832. This example code is done by using timer and i could not understand how to use timer. We...
hi all ,
i now need porting nrf_libuarte_async lib for my project . it show some error
How to deal with this problem？
i reference (experimental_libuarte project...
Hi everyone;
I wanna send to data my uC from my phone. I looked peripheral uart example. This example use only send data phone from nrf52 SoC. What can i do? How I add...
Hi All
I have developed some code by modifying the 'ble_app_multiperipheral_pca10056_s140'. I have tested my code on the NRF52840 DK board (PCA10056) and everything seems...
