I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hello,
Now i use NRF51822 DK with code in attachment to test app_timer hangs.
Fristly , you can press button 0 to start a 100ms app_timer, and we can see it through uart...
I am attempting to use Enhanced Shockburst/Gazell working with coded PHY, in order to achieve long range communications with very lower power consumption. I have searched...
Hello, I am experimenting with your nrf5SDKforMeshv310
I can compile and download the included examples.
Because I own a few Thingy 52, I wish to flash them as light_dimming_servers...
hi,
I am trying to add SPI (master) codes into the ble_app_uart.
My setting for SPI is as follows:
#define SPI1_ENABLED 1 // #define SPI_INSTANCE 1 /**< SPI instance...
Hi I am using nRF52832 board amd i am trying to debug ble_app_uart as Central.
BLE connection is established between this central application and the peripheral.
Opened...
i am using nrf24l01+ on arduino devices, one arduino device as master, and other arduino devices as slaves. I like master to broadcast a radio (dataToSend) toward all slaves...
nrf52832, keil with startups from sdk13
Initialization:
IntHandler:
With one event everything working well. Then I add another:
I need to measure SENT signal...
hi.... folks
i am using nrf52840 development kit , and i debugged the merged programs such as uart and twi program in it .does it will give the temperature data?
i am...
Hi all,
Please refer to the SDK version : nRF5_SDK_15.2.0_9412b96.
We need to use two uarts simultaneously for module & device respectively.
For example :
UARTE0 ...
We, I am using nRF 5 SDK v 14.2.0.
Power-off has occurred during program development. I can not identify the location, Functions that are not memory leak, buffer overflow...
Hi,
Now, I am using the nRF52840 to develop and do signal test. Can you share me some tool that can make the board enter the test mode?
Best regards
Simon
Hi:
PREJECT: nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_hrs_freertos\pca10040\s132\arm5_no_packs
When TWI0 and GPIOTE are turned on at the same time, the...
I'm trying to get the AT commands sent in the asset_tracker example written out together with the other printk statements. I have tried adding this to the prj.conf: CONFIG_LOG...
I used the nrf52840 as the central device, use SDK15.0, scan then connect the peripheral toys.
sometimes i found the central can scanned some ble peripheral but can't connected...
