Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Hello, i am having problems with a loop in the function "flash_manager_wait()"; in the begining of the code.
main()-> initialize()-> mesh_init()-> mesh_stack_init(&init_params...
Hello, I have a discovery issue that seemingly only happens with the Samsung Galaxy S8.
I want to throughput test BLE5.0(2Mbps).
I using the nRF52832(BMD-300) with SoftDevice...
Hi!!
I'm adding spi functionality to S132 and SDK 14.0.0 ble_app_uart now.
The communication which added the function of UART to SPI and the sample code of ble_app_uart...
hello,
Now, i want to recover MAC from static random state.
for example, if MAC[5] =0X55 in chip itself, The MAC in adv in 0x1101 0101 ;
but i want mac in adv is 0x55...
I am using nRF52 SDK v15.2.0, nRF SDK Mesh 3.0.0, and Segger v4.1.2.
I keep getting Mesh Error 6 while trying to combine the provisioner role with the client model. Which...
Hi,
I'm using nrf51822 with a custom board, where I should turn on a buzzer sometimes. I configure a timer and ppi to make a bip alarm. each bip lasts about 1sec; and the...
hello! i have a problem ,when the Master send Slave SMP 37 Rcvd Pairing Request: Bonding, MITM, Initiator Key(s): LTK IRK CSRK , Responder Key(s): LTK IRK CSRK,but the slave...
hello! i have a problem ,when the Master send Slave SMP 37 Rcvd Pairing Request: Bonding, MITM, Initiator Key(s): LTK IRK CSRK , Responder Key(s): LTK IRK CSRK,but the slave...
Hello,
Thread Topology Monitor can associate an user name with a device. Where is it stored (in computer application or directly into the device) ? If it's in the device...
Hello All,
I am trying to interface an analog sensor with nrf52832, whose analog values have to be converted using SAADC and has to be sent over SPI to another chip. But...
I am testing the NR52832 using a BMD350 module on a custom made board.
Using the SPIM i faced the problem that i got an extra 500uA of current randomly. After trying to...
Dear Nordic,
We are using NRF52832 + RFX2411N for our product, and for lower the power consumption. we wonder if there has any way to know the CONNECT_REQ event.
In advertising...
After some time debugging an issue I had, I found out that my code was setting the I2C interrupt priority to 0, and at the same time that I'm running a Soft Device on my nrf52832...
Hi,
The Ch. 16 Power Supply Section of "nRF52840 Objective Product Specification v0.5" mentions the two power supply mode of nRF52840. This supply is available on the respective...
Hi.
I’m trying a multiperipheral function and have a problem.
The problem is I can not notify stable battery voltage with SAADC to the connected Central while advertising...
