Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
I have a case where I'm using a timer/counter as a counter with one PPI channel routing a GPIO rising edge to the COUNT task. Another GPIO rising event controls the counting...
I have an nRF52 paired to a central device. In order to delete the pairing on the nRF52 I clear the persistent data (dm_init_param_t).
I notice, however, that even though...
Hi all,
I'm a grad student trying to innovate on the BLE concept. I require a continuous signal as a source: preferably unmodulated, but a long duty cycle could also work...
The NRF52 product specification (aka, datasheet) has 3 chapters in it all relating to TWI: TWI (chapter 49), TWIM (chapter 33), and TWIS (chapter 34).
Which section (TWI...
Hi,
I'm trying to interface SIM808 with nrf51822 over uart using nrf_drv_uart. Everything works well for some time, but then uart starts reporting error code 1, NRF_UART_ERROR_PARITY_MASK...
Hello,
I am working with the GPIOTE library to get a GPIOTE_IRQ from a peripheral.
I have several questions regarding the library and how IRQ works.
1.How do I clear...
Hello,
I am using SDK7.1.0 for NRF51822.
In my subroutine, I would like to disconnect with the peer device, and re-advertise. But when after re-advertising, I found the...
Is it possible to set scope for search in info-center only for SDK 11? It search in all SDK versions and sorts results randomly. It is very annoying. Especially when there...
Hi,
I want to build expertise in BLE and want to use the Nordic nRF51x22 to build a hardware and write the firmware for the same.
I am planning to use the nRF51 DK....
I'm calling sd_ble_gatts_characteristic_add multiple times to add characteristics to a peripheral. At some point I get a return value of 0x200020B6. I'm not making much headway...
Hello everyone,
I am trying to use the ble_app_hrs_rscs_relay example from SDK V11 for s130 (2.0.1).
It compiles and works well when I use an pc10028 evaluation board...
If I have multiple services, 2 for example, how should I set up the srdata.uuids_complete.p_uuids in the code:
ble_advdata_t srdata;
memset(&srdata, 0, sizeof(srdata)...
Hello,
I am developing beacon on nRF51DK and I want to store in non volatile memory some parameteres like:
ProximityUUID
Minor
Majnor
AdvInterval
Tx_power...
Is it possible to configure SPI Master API to send multi-byte words?
My peripheral expects transfers in 16-bit blocks (CS goes low, 16 bits are clocked in, CS goes high...
Hi guys,
I'm going to start the development of a new project based on nrf52832 and I have to decide the firmware architecture and APIs. Designing the support for the Nordic...
