The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi,
I recently bought the nrf 51 development kit. Before implementing a BLE application on the board I wanted to start with a simple application of blinking a LED by pressing...
1.I have a nRF51_DK and nrf51822(waveshare core51822)
2.Keil 5.18v and all of the needed software were Installed
3.s130 1.0.0 or 2.0.0 and sdk9.0 or 10.0 were used ...
Hi Nordic Dev Zone, Ray Kampmeier here.
I'm building Direct Test Mode (DTM) into a production application that uses the 110 soft device. Unlike the provided Nordic examples...
Is there any way to integrate SoftDevice with entire project so I can get one hex from build? I am new to CrossWorks and nRF52 and I am developing BLE device. After getting...
I want to do firmware update over the air in a STM32F4xx microcontroller which is connected with nRF51822 chip via UART (TX, RX, CTS, DTR) and BOOT pins. ST microcontroller...
Hi
I can get the current time from the server using the time service characteristic. Which function should I use to set the RTC clock on the nrf 51 to the current time...
When I add a new server of my own service I got a problem.
when I set
BLE_GAP_CONN_SEC_MODE_SET_ENC_NO_MITM(&cccd_md.write_perm);
I can send data to iOS normal,but...
Sometimes I only need to send 4 bytes instead of twenty using a notification. I've noticed the init_len and max_len parameters but I'm under the impression that this will...
i am already using sdk 10. but when we have build boot-loader program. so, generate "nrf51422_xxac.hex" file. it's working for only nrf51422.. but not for nrf51822. so, how...
Is there any difference in RAM overhead with the new app_timer module on SDK 10?
I'm my application on SDK 6.1, I have 25 app_timers which run without any issue.
APP_TIMER_MAX_TIMERS...
I am setting up production testing of our product to do RF testing per app note AN34. We are using the nRF51822 on our product. I'm using Nordic's development kit and their...
Hello,
I am planning to use the nRF51 device in DTM and was looking for help on how can use it to control via USB/UART connection to PC using FTDI chip. All I want to do...
Hi Nordic,
I am having a problem with linking against either of the gazell gcc libs (gzll_gcc.a or gzll_sd_resources_gcc.a).
I'm using Yotta (MBED) and have taken the...
Hello,
we have an android/iOS app on a phone that is connected to my button (nRF51) and to a Bluetooth headset. The app is a kind of walkie talkie that transmit mono audio...
