nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I am using nRF5415-DK and SDK v3.2.2
I want to generate a sine wave using PWM and TIMER. The PWM repeat duty cycle method has limitations, so I am using a timer to trigger...
Hi, for one of our products we are evaluating an option of porting the application from nRF5 SDK (nRF52) to nRF Connect SDK (nRF54). Seeing the similarity between the nRF...
Hello DevZone,
I am currently trying to fix an issue I have on deployed devices, using nRF9160 with nRFCloud. Code is based on SDK 2.8.0.
In most cases, my code works...
I am attempting to use the nRF52840 QSPI periphery to communicate with an SRAM chip. The chip is IS66WVS8M8FBLL-104NLI. I am unable to communicate with it using QSPI. I am...
Hi everyone,
For mthe prject I'm working I must use the LPCOMP module to detect a cross. but anytime a init the LPCOMP module my code seems to freeze and nothing else...
Hi,
I have developed a Matter-over-Thread light bulb using the Silicon Labs EFR32MG24 platform, with CHIP_CONFIG_SECURITY_TEST_MODE = 1 enabled. In parallel, I have set...
I am currently porting an internal application to the nRF54LM20 and am attempting to manually trigger a GPIOTE30 interrupt via software.
Observed Behavior:
Hardware...
Hi,
I am working on a custom board which is NRF54L05 connected to NRF54l15 DK via P19
NRF54l15 DK version: PCA10156 0.9.3
Serial wire debug cable length: 15cms
Breakout...
I'm kind of stuck here. I was using SES v3.52 on Mac OS Sequoia and everything worked fine. I upgraded my MacBook to Tahoe and all of the fonts were messed up making it un...
Hi.
Using Thread Topology Monitor and NRF52840-DONGLE I'm able to connect to the device and getting the UDB device to be a Thread Leader.
But how can I join an existing...
I am using the command AT+CRSM=176,28539,0,0,12 to attempt to read the FPLMN on the my nRF9160 DK. The modem firmware version is 1.3.5. See attached logs:
(14:11:15.629...
I have built the Matter temperature sensor sample for the nRF5340 running on an nRF7002DK (no WiFi enabled). The power consumption measured with a PPK2 is coming in higher...
Hello,
I am developing Channel Sounding Test Mode functionality using nRF Connect SDK (NCS) v3.1.1 and the nRF54L15 Development Kit (DK) , based on Nordic’s official hci_uart...
I am adding a feature to our device to actively connect to a Bluetooth printer and send data to it, but I am now encountering an issue that I cannot solve.
I currently have...
Hello.
I am considering using the UICR OTP to store device-specific identification information. My understanding is that when accessing this area from a Non-secure application...
