Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi,
I'm working through building my own Matter device. Building on MacOS, VSCode on 2.7.0. I'm using an nrf52840DK for now.
I have two endpoints that contain a temperature...
https://community.element14.com/products/roadtest/rv/roadtest_reviews/1646/draft_for_nrf5340
Above link is a user experience with one of you development kits, which is typical...
Hi, we are working on an application that makes heavy use of work queues. We'd like some way to monitor work queue events to optimize timings/priorities etc. I was looking...
I am trying to make a remote control with NRF24 and Atmega328p. The full name of the NRF24 I am using is E01-ML01SP2. I fixed everything but it draws too much current. I have...
We are looking for BLE Mesh Sniffer,
it has come to our notice nordic provides nrf sniffer. can we sniff BLE Mesh Packet?
Will this mentioned link sniffer be of any use...
Hi all,
I have developed a project for nrf52811 on nrf52840DK.
My question is how I flash this project into nrf52811 using nrf52840DK.
I am using nrf5 sdk 17.1.0...
Case 1: Constantly power on reset during the network attachment process. The customer produced 2000 pcs , 300 pcs defective rate. We measured the voltage of VDD1 and VDD2...
I modified the BLE fundamentals lesson 5 exercise 2 example ( github repo ) for my purposes. This uses a generated passkey for pairing with accept lists.
I removed the...
I've had success getting the Sigurd Hellesvik Serial Recovery sample to work on an nRF52840 DK with mcumgr cli commands. I'm able to flash the Fanstel 840 with the same bootloader...
How do I resolve/update:
zephyr-sdk is outdated. Found 0.16.5, but 0.16.8 is required by the SDK.
python is outdated. Found 3.9.13, but 3.12.4 is required by the...
Dear Nordic Support Team,
I am encountering a persistent error while setting up NRF Connect for Visual Studio Code. Despite numerous troubleshooting efforts, I have been...
Hello,
I want to use the PPK II in a free-running state in Scope mode, which is the same behavior that most oscilloscopes refer to as Auto triggering, but it appears that...
Hi!
I am using direction_finding_connectionless_tx/rx sample, and NCS v2.6.1 for AoA.
RX board: nrf5340 devkit + antenna
TX board: nrf5340/nrf52833 devkit
Problem...
I didn't see an issue tab on the Github page for sdk-nrf, so I'm proposing this here.
My device acts as both a central and peripheral, but as a central role I am connecting...
Hello,
I am using the nrf21540 with the shield nrf21540ek; nRF Connect SDK 2.6.2 and the toolchain 2.7.0.
Currently I am getting the following warning on the log output...
