Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
Hello,
By using nRF Connect SDK v2.6.1, I want to have RTC (Date Time, Calender, etc) functions, so I modified the code based on one of Nordic Academy examples, which can...
Hi,
I've resumed working on my project with the nRF Connect SDK after a brief break. However, when I try to run a simple project, I occasionally encounter an error while...
Hello, I've recently purchased an npm1100-EK schematic from Digikey. The evaluation board works great but I can't find the Schematic & hardware files for this particular version...
Hi everyone. I'm using nRF Connect SDK 2.6.1. I'm implementing LittleFS for file management on an external QSPI-Flash. I need to format the flash and erase all of data. I...
Hello,
I am currently researching the best way to be able to change the rate at which I fetch a GPS fix. I want to start the program at 60 seconds, then depending on environmental...
This is a continuation of this question . It may be necessary reading to understand the context.
I 'm confused by this topic too, however I think the error about "boot_partition...
Hi,
I'm trying to build the MQTT sample for a custom board, trying to communicate between nrf52840 and nrf7002 via QSPI. Here's my board definition:
In the build configuration...
Hello everyone,
I Have a LTE reconnection issue after LTE signal loss with SDK 1.3.6. I was doing some LTE connectivity tests by placing the board in a faraday box. After...
Hello! We have developed a custom board featuring an nRF9160 and an ESP32-C3-MINI-1 co-processor, which is flashed with AT-firmware (version 3.2.0.0). Our current application...
Good morning, if I wanted to develop a board with the VM3011 device, where can I find it? It seems impossible to find it as a device in major stores, and I can't even find...
Hello,
I would like to develop a temperature logger which Starts to log temperatures between certain limits
The data is stored until the device has connectivity to the...
Hello,
I know this issue has been discussed extensively in different posts, and I believe I read all of them, but still I can't get it working.
I'm trying to drive...
Hi,
I'm trying to run the i2s output sample from NRF Connect SDK 2.7.0 on the nrf52840 DK, and I'm only getting the clock signal from P1.15, and no signal from any of the...
I'm just a bit fuzzy on how all of the bootloader stuff comes together.
Our application is small (100K-ish), so a dual-bank strategy seems appropriate.
It uses a proprietary...
