I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
I have printed and assembled this circuit. The board is programmed with the help of a development board, but it doesn’t work. What could be the problem?
my code (led toggling...
nRF_Segger_RTT I want to port it from the high version SDK14.2 SDK to SDK7.1, is it OK?
Will it be difficult?
Can it be transplanted?
Tell me, thank you
Dear team,
I would like to have a function to measure the pulse width of the pulse that I generated and wonder if that is possible.
For example, I can generate one pulse...
I'm trying to create a demo beacon with an advertising interval of 5s and I only ever see a single advertisement from the device, following boot up. I've encountered this...
Hello,
I have an issue where my PC suddenly can't use any JLink after it had previously been working. Nothing changed to my knowledge that would have caused this issue other...
Hello,
I'm trying to enable the Power management for nRF9161 over nRF-Connect SDK2.5
the prj.conf has an entry of 'CONFIG_PM=y'
but it not accepted because we do not...
I've received a Nordic Semiconductor nRF9161 from a friend, who has been using it for a while.
I would like to completely reset the module, as it came when bought, so...
Im trying to use the BMA4xx driver (via i2c) in 2.7.0. The driver seems to init the device ok but I am getting a "SECURE FAULT" as soon as I do a sensor_sample_fetch . Attached...
Hi,
I spend few day trying to understand the issue with the provided sample (followed the tutorial) in the IoT fundamental lecture for the MQTT protocole. Then, I tried...
Hardware: nRF52840 (Custom Hardware)
Software: nRF Connect SDK v2.6.1
I am using the nRF52840 with custom hardware, where the device operates in two modes: Sleep Mode...
Hi,
In my project, I need turn on/off the hfxo, I found when i configure the hfxo, the nfc is not working. Here is my code:
void gps_server_function ( void * p1 , void...
HW: NRF52832 DK SDK: 17.1 SD:S132_7.2 Sw: ble_uart_c Issue: nRF52832 as a central to scan a peripheal(not nordic chip),the nRF Connect APP can discovery all the service, but...
I am trying to connect RPI(and/or Nvidia Jetson) with nrf9160 custom board(Icarusv2). I am using this custom board for other purposes and it works fine. For now I found only...
Hei,
I need to find the documentation for the NRF SDK 1.8, there's a page which has links to all the documentation versions:
https://developer.nordicsemi.com/nRF_Connect_SDK...
Hi,
I am working with nRF52840 SoC (custom board) and AT25QL641 QSPI Flash chip. I am on v2.1.0 of nRF Connect SDK. The slot1 (update slot) is on an external flash.
...
